Fiat 500 Replacement Key Fob

If your remote key fob has stopped working, it might be time to replace the battery. If you replace the battery and it doesn't work it could be the issue elsewhere.

At United Locksmith, we specialize in the creation of new keys for old cars. We have all of the tools and parts necessary for this type of service.

Dead Coin Battery

The most frequent reason that your Fiat 500 key - gwwa.yodev.net, fob will not unlock or lock the doors is a dead battery. The battery for the coin cell in the key fob will deplete quickly when you don't use frequently enough. If your remote has started to show signs of a loss of range or has stopped functioning in the middle of the night, then your battery may be dead.

The battery in the key fob is held in place with metal clips that retain it. If the clips are loose they can cause problems with contact, which can prevent the remote from receiving power. Make use of a flathead screwdriver to remove the retaining clip and remove the old battery. Make sure you use a replacement with the same type of voltage, size, and specification as the original battery.

The exposure to water can cause the key fob to corrode or become damaged. Even a brief bath in soapy water could harm the electronic chip in. It is recommended to keep your key fob in a dry environment.

Water Damage

Water damage may be the reason for your key fob's not functioning properly. The rubber seals on key fobs stop them from getting damaged by a small drizzle or splash of water. However, it is crucial to keep your keys from the ocean, washing machine, and even the pool.

The key fob has an electronic chip which sends a message to the immobilizer system of your vehicle. The chip allows the 500 to be locked and started. If it gets wet, however it won't function.

You can clean the inside electronics of your keyfob with isopropyl Alcohol or an electronic cleaner to determine whether they're still in good condition. It is recommended to replace a key fob in the event that it's submerged into salt water rather than attempting to repair it yourself.

A replacement fob may cost you a few dollars, but it's a lot less expensive than paying to have your Fiat 500 towed to a dealer and repaired there! In addition, you can make it yourself in just the simplest of steps. Be sure to use the right battery type before you attempt to open your key fob. You can find step-bystep directions for any car keyfob online.

Faulty Chip

The chip located within the key fob communicates with the car's immobiliser system to ensure the car is able to start when the correct key is inserted. If the chip is damaged or damaged in any way the car won't start.

Damage to the water or a dead phone battery are the most common reasons for an unreliable chip. Whatever the reason, it's an ideal idea to hand the work to a locksmith since they will be able to repair the chip quickly and at a cost-effective price.

If your key fob stops functioning after exposure to clean tap water or rain, take off the battery and clean the electronic component using a paper towel to ensure it is fully dry before putting it back into. If the key fob doesn't work it's most likely to be a damaged chip and is required to be replaced.

Some people will turn to their dealer when they are in need of a new Fiat key fob, but it can be a costly option. United Locksmith is the best choice if you need your Fiat key fob repaired at a reasonable price. We have the equipment and know-how necessary to repair your fiat 500 key replacement key fob in a timely and professional manner.

Faulty Receiver Module

Fiat key fobs transmit a signal to the vehicle that can unlock and lock doors (and start the car for those with an automatic transmission) up to 50 feet. There are a variety of reasons why a fob could not function. This can be caused by a dead coin-battery water damage, worn-out buttons, a receiver issue, signal interference or a malfunctioning chip.

If the fob has been in a pocket that has endured extreme trauma, like being dropped on hard floor or being washed in a wash machine or dishwasher, it might not be capable of communicating with the car's Body Control Module (BCM). This is because the BCM is secured and will only accept a signal from a genuine key and not accept any other.

You will need to replace the fob if this happens. A professional locksmith is able to handle all aspects of the key replacement process and even program a new one for the 500. They can even give you an clone fob that performs just like the original (and costs just a fraction of what it would cost).