Fiat 500 Replacement Key Fob

It's possible to replace the battery if the 500 remote key fob isn't working. If you do replace the battery but it does not work then the issue is likely to be elsewhere.

United Locksmith specializes in the production of new keys for classic automobiles. We have all the necessary tools and parts to perform this service.

Dead Coin Battery

The most frequent reason why your Fiat 500 key fob will not unlock or lock the doors is due to a dead battery. The battery for the coin cell in the key fob can be depleted quickly when you don't use it often enough. If your remote is beginning to show signs like a loss in range or stopped working or not responding, then the battery could be dead.

The battery inside the key fob is held in place by metal clips that hold it in place. If the clips are loose it can cause contact issues that will stop your remote from receiving power. Using a small flathead screwdriver, pull the retaining clip to remove the battery and insert a new one. Make sure you use a replacement battery with the same type of voltage, dimensions and specifications as the original battery.

The exposure to water can cause the key fob to corrode or be damaged. Even a brief shower in soapy water can harm the electronic chip within. It is best to keep your key fob in a dry environment.

Water Damage

If your key fob isn't working correctly, it could be caused by water damage. Key fobs come with rubber seals that prevent them from being damaged by light rain or a splash of water, however it is crucial to keep your keys out of the pool, ocean, and washing machine!

The key fob is equipped with an electronic chip inside it that sends a signal car's immobilizer system. This is the reason why your 500 can start or lock, but when the chip becomes wet, it can no longer work.

You can try cleaning your key fob's internal electronics using isopropyl alcohol or an electronic cleaner to determine whether they're still in good condition. However, it's recommended to purchase a replacement from a dealership instead of trying to fix the key fob which has been submerged by salt water.

Although a replacement fob may cost you a little bit of money, it's far less expensive than paying for your fiat panda key fob replacement 500 to be towed to a dealership and fixed! You can also do it yourself by following only a few steps. Make sure you have the correct battery type before you attempt to open your key fob. You can find step-bystep instructions for every car keyfob online.

Faulty Chip

The chip that is contained in the key fob communicates with your car's immobiliser unit to ensure the car is capable of starting when the correct key is used. If the chip is damaged or damaged in any way your car will not start.

A chip that is defective can happen due to several reasons, but the most common cause is water damage or an unresponsive battery. It is best to hand over the job to a professional locksmith who can repair the chip in a short time and at a reasonable cost.

If your key fob stops functioning after exposure to clean tap water or rain, remove the battery and clean the electronic component with a paper towel to ensure it is fully dry before putting it back in. If the key fob does not work, it is likely an issue with the chip and is required to be replaced.

Some people will go to their dealer if they need a new fiat replacement key fob. But, this can be an expensive option. United Locksmith is the best choice if you would like to have your Fiat keyfob repaired at a reasonable cost. We have the equipment and know-how needed to repair your Fiat key fob in a quick and professional manner.

Faulty Receiver Module

Fiat key fobs send a signal up 50 feet away to the vehicle, which will unlock and close the doors (and start the vehicle if it has automatic transmissions). However, there are several things that could cause the fob to cease functioning. This could be due to a dead coin battery water damage or worn buttons, a receiver module issue and signal interference or an electronic chip that has failed.

If the fob has been placed in a pocket that suffered a severe trauma, like being dropped on hard floor or getting washed in a wash machine the fob may not be capable of communicating with the car's Body Control Module (BCM). This is because the BCM is a secure system that will only accept signals from a genuine key and not another.

You will need to replace the fob in case this occurs. A professional locksmith will take care of the entire process of replacing keys including programming a new one for your 500. In fact, they'll provide you with a duplicate key that works just like your original fob (and costs only a fraction of the price).