How to Replace a Kia Sportage Replacement Key

The key in many Kia models comes with a keyless entry system built in. The key functions like remote controls and is exchangeable by an Kia dealer.

Key fobs can fail to function due to a number of reasons, including a dead battery, worn-out buttons, signal interference or water damage. Here are some suggestions on how to get your Kia Sportage replacement key back to working.

How do you replace the remote key or the smart key?

The battery in your Kia's intelligent key will eventually need to be replaced, regardless of whether it is a remote key, a push-to-start key or a regular metal key that is not equipped with a transponder. This is especially the case if your car shows a message that states the smart or remote keys are in poor condition.

Fortunately, it's quite simple to do. To replace the battery on the keyfob take out your mechanical key from the slit that is located at the back of the fob. Then, you need to pry the cover off. Inside the key fob there will be the small screw that holds the battery in its place. Using a small screwdriver, unscrew the screw and pull out the old battery. Then, insert the new and close the slit inside the key fob.

Test the key fob by pressing the lock or unlock buttons. If the doors unlock and lock exactly as you expect, then you're set! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or when you need to run errands around Brandon.

Note: Some key fobs (transponder chip or smart keys) may require their programming completed. This requires a computer, which is only available to the locksmith for cars or dealer. Other keys (non transponder metal keys), do not need programming. If your key requires to be reprogrammed, you will need to be aware of the key code number written on the tag that identifies the key and then record the number in a secure place.

How do you replace the battery?

If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a sign that the battery should be replaced. A low battery may also cause other issues such as the check engine light flashing on or a delay in cranking the engine. Fortunately, replacing the battery on the key fob is a relatively simple DIY task that requires only some basic tools.

Before starting the process, make sure that your vehicle is turned off and that all doors are closed. Find the small metal or plastic piece that is located at the bottom of the key fob. Then, jiggle it until the key comes out. Then, you can put the key into the door handle of the driver to unlock your car.

To replace the battery inside the key fob, remove the cover that covers the rear. Use a plastic pry tool to remove the latch that holds the black negative cable. Remove the old battery and then orient the new battery in a way that the "+" positive side is facing your face and the "-" negative side is facing towards the fob's metal electrical contacts. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid bending or damaging the metal contacts.

After installing the new battery after which you turn the key fob off and on in the ignition until the door locks up. Then, you can test your Kia key fob to check if it is working properly again.

How do you replace the smart key?

Depending on the model of the Kia Sportage, you may have a standard key fob or a smart key. The smart key features an embedded mechanical key blade, while the standard key fob does not. Both key fobs have batteries that will eventually require changing. Fortunately, it's an easy task that only takes about two minutes.

Before you get started before you begin, ensure that you are on a level surface with enough lighting and that your kia picanto key replacement is off. Keep in mind that there are small parts inside the fob that could be removed if not vigilant.

The first step is to find the small release button on the back of the lower part of the fob. It will be an oval or circular slot. You can open the key fob by pressing the button.

Once the key fob is opened, remove the battery that was in it. The new battery is C2032, and can be bought through the internet or at a local auto parts store. After you've finished, you should be able to lock or unlock your vehicle using your key fob - even if the engine isn't running!

How do you replace a broken mechanical key

The Kia keyfob is a great convenience that allows us to lock or unlock our car by pressing one button. As with all devices that is used, the Kia key fob can occasionally have problems. There are solutions to solve these issues and keep your key fobs functioning for the duration of.

A low or dead battery is one of the most common issues. The battery could cause the device to stop working or work intermittently. If this is the case then try replacing the battery with a new one.

If this doesn't fix the issue then try using a normal flat-head screwdriver to break open the fob's plastic casing. Be careful not to harm any internal components or scratch the plastic. Once open, carefully remove the battery you have been using and replace it with a brand new one.

After the new battery has been put installed, close and unlock the doors using the mechanical key (every kia key replacement fob has an emergency mechanical key that can fit into the slot). Test the key fob and verify that it's working correctly. If the device isn't functioning, contact a dealer or locksmith to resolve the problem. To avoid a lockout in the future make sure you get an emergency key that can work on all door and trunk cylinders.