Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinctly SUV-like appearance due to its larger dimensions. Additionally, the ride on 19-inch wheels in Ti and ST-L models may be a bit stiff at times. The front tyres of Qashqai can also lose grip on rough surfaces, and its CVT can sometimes show wrist-flexing torque steering.

This is usually due to the battery of a coin that is dead. It is easily replaced in minutes. Make sure the Replacement Key For nissan micra, Ivimall.com, battery is of the same size, voltage, and specification.

Water Damage

One of the most common reasons why a Nissan key fob gives the "key ID incorrect" message is due to water damage. The rubber seals on the key fob are designed to protect the chip's electronics, but long-term exposure to moisture can cause it to malfunction effectively. It's common to see this if your key fob has been dropped in the ocean or in a pool. However, it could also occur when it becomes wet from showers or soapy hands.

If your key fob was exposed to water for a long period of time it is possible to clean it with isopropyl, or an electronic cleaner. Or, it could require a visit to an expert to repair or replace it.

If your key fob needs to be replaced, it's an easy process. Make sure you have the right multipack (CR2032 3V). Open the front and rear cases with a flathead screwdriver. Remove the metal clips, remove the battery that was in place and replace it. Reassemble the fob and replace the mechanical key. Make sure it's working properly. If not then you'll have to go to your local Nissan dealer or an expert locksmith to replace the key chip. Fortunately, the chip is not typically damaged by exposure to water and therefore this shouldn't be a major expense.

Dead Coin Battery

Another common reason your Nissan Qashqai key fob might not function is because the battery in the coin has gone dead. These batteries usually last 3-5 years, but they can become depleted in time, particularly when the fob is frequently dropped. You can try replacing the battery with a new one but be sure it's the same voltage and size as the original. If you are using another battery, it may cause the key to have an untrue key ID, which will prevent it from paired with your vehicle.

The best method to replace the coin battery on a Nissan Qashqai key fob is by prying open the key fob using the small screwdriver with a flat-head. The screwdriver should be inserted into a small notch at the bottom of your key fob. Gently twist the screwdriver to separate the two halves. Remove the old CR2025 battery and replace it with a new one, taking note of the location of the old battery in the fob.

Check the terminals for water damage or dirt before installing the new battery. If there is, wash the terminals using a small amount of isopropyl alcohol. Make sure that the pole cables are connected correctly. They should be connected to both the negative and the positive poles of your battery.

Troubleshooting

If your Nissan Qashqai key fob stops working after exposure to clean tap water or rain, it may be an indication of a chip issue inside. You'll require a new nissan key fob if you can't fix the problem by changing the battery. If you dropped the key fob on the ground and it stopped functioning immediately it is likely because it damaged the internal chip. It is usually possible to get the key fob back to work once again if it is removed and clean the chip with alcohol and paper towels, then put it back into.

A common error that you may notice on your dashboard is "Key ID Incorrect." This means that the car cannot recognize the key fob and will not allow it to start the engine. This problem could be caused in several ways, such as water damage, issues that are undetectable in the circuitry of the key fob or RFID interference.

The key fob will stop working when the 12 volt batteries are dead or don't provide sufficient electric current. This could affect the remote keyless system and central locking in your Nissan Qashqai, as well as making it impossible to start the engine with the key fob (if equipped with Intelligent Key). Check the batteries inside the key fob if it is in a position to lock or unlock your door by hand. Try reconnecting the battery in order to reset your transmitter.

Reprogramming

If the key fob was not submerged in saltwater, it should be able come back to life with a simple wash of clean water. You can also clean the electronic component using isopropyl or electronic cleaner. If none of these works, you may have to replace the key fob.

If your Nissan Intelligent Key is still not working, there could be a problem with the connection between it and your car. Start by turning the ignition key but not activating the vehicle. Keep doing this until you see the warning lights flash twice. Then, turn the car off and take away the keys.

Next, open the fob compartment of your vehicle. It's usually located in a door jamb on the handle on the driver's side or under the armrest. Find the button that says "program" and press it. When the process is complete, you should hear the sound of a chime.

Now that your Intelligent Key is relinked to the car now is the time to try it out. Take a step away from the vehicle and click all of the buttons on it. If the lights flash, or the horn sounds, the key is successfully connected to the Nissan. You can also test it close to the Nissan.