How to Replace a Kia Sportage Replacement Key

For a variety of Kia models the key comes with a built-in keyless entry system. The key functions like a remote control and can be exchanged with a Kia dealer.

Key fobs might stop working due to a number of reasons, including an inactive battery, worn out buttons signal interference or water damage. Here are some suggestions to help you get your kia picanto key replacement (this site) key fob that is a replacement for the sportage again.

How do you replace a remote key or smartkey

No matter if your Kia is equipped with an intelligent key, remote key, push-to-start key, or a regular non-transponder steel key the battery in these keys will eventually need replacing. This is especially relevant if your car displays a message that the smart key or remote has a low battery.

Luckily, this is quite simple to do. To replace the battery in the keyfob remove your mechanical key from the slit at the back of the fob. Then, push the cover open. Inside the key fob will be tiny screws that hold the battery in place. Remove the old battery by unscrewing the screw with a small screwdriver. Then insert the new one and close the slit inside the key fob.

Test the key fob by pressing the lock/unlock buttons. If the doors lock and unlock according to your expectations, then you're good to go! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you need to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming completed. This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder keys made of metal), do not need programming. If you need to reprogramme your key, you'll need to write down the key code's number on the tag for the key code.

How to replace a battery

If the Kia key fob does not respond to pressing the lock or unlock button, it is likely that the battery is not fully charged. A battery that is not functioning properly can cause other issues, such as the check engine light turning on or the engine not cranking correctly. Fortunately, replacing the key fob battery is a fairly simple DIY project that requires just the most basic tools.

Before you begin the process be sure that your vehicle is turned off and that all doors are shut. Find the small, metal or plastic piece on the bottom of your key fob, and play with it until a metallic key slides out. This key can be placed inside the driver door handle to unlock your car.

To replace the key fob's battery, take off the cover on the rear and use a pry bar tool to loosen the latch holding the black negative battery cable. Remove the old battery and orient the new one to ensure that the "+" positive side is facing you and the "negative" negative side is facing the fob's electronic contacts. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid damaging or bending the contacts made of metal.

Once the new battery is installed and the key fob is turned on, turn it off and back on in the ignition repeatedly until the door locks. Then you can test your Kia key fob to see whether it's functioning properly again.

How do I replace a smart key

Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The smart key comes with an embedded mechanical key blade, however, the standard key fob does not. Both key fobs come with batteries that will eventually need to be changed. Fortunately, it's quite simple and takes only two minutes.

Make sure you turn off your kia replacement key fob and stand on a flat or well-lit surface prior to when you begin. Also, remember that there are tiny pieces inside the fob that can fall out if you are not careful.

The first step is to locate the small release button that is located on the lower backside of the fob. It could be a circular silver button or a rectangular slot. You can open the key fob by pressing the button.

Once the key fob is opened, remove the old battery. The new battery is a one called CR-2032 and can be bought through the internet or at a local auto parts shop. After you've finished with the battery, you should be able to lock or unlock your vehicle with your key fob even if the engine isn't running!

How do I replace a mechanical key

The Kia keyfob is a wonderful convenience that lets us lock or unlock our car by pressing a button. However, like all devices it may have issues at times. There are ways to fix these problems and keep your key fobs running for an extended period of time.

One of the most common problems is a dead or dead battery. This could cause the fob to cease working or even to stop working intermittently. If this is the problem you should replace the battery an entirely new battery.

If this doesn't fix the issue Try using a standard flathead screwdriver and wedge it into the casing of the fob's plastic. Be careful not to damage any internal components or scratch the plastic. Once the battery is removed and replaced, you can replace it with a brand new battery.

Close and open the door using the mechanical key. (Every Kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob to verify that it's working correctly. If the key fob not working, contact an authorized locksmith or dealer to solve the problem. To avoid a lockout in the future make sure you get an emergency key that will work in all of the door and trunk cylinders.