How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models comes with an electronic keyless entry system built in. This key usually resembles a remote control and can be changed with a new one from an Kia dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, including a dead battery, worn-out buttons, signal interference or water damage. Here are some tips to assist you in getting your Kia sportage replacement key to work once more.

How do you replace a remote key or smartkey

No matter if your Kia comes with an intelligent key, remote key, push to start key or a regular non-transponder metal key, the battery in these keys will eventually need replacing. This is especially the case if your car displays a message that indicates the smart or remote keys are not powered by batteries.

This is a relatively easy procedure. To replace the battery on the keyfob take out your mechanical key from the slit that is located at the back of the fob. Then, you need to pry the cover open. A small screw will be inside the key fob, which holds the battery in its place. By using a small screwdriver unscrew the screw and pull out the battery that was in place. Then insert the new one and close the slit inside the key fob.

Test the key fob by pressing the lock/unlock buttons. If the doors lock and unlock according to your expectations, then you're all set! You can now make use of the hands-free lock/unlock feature on your Kia whenever your fingers get chilly or you have to make errands in Brandon.

Not all key fobs could need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non transponder keys made of steel) don't require programming. If your key has to be programmed, you must be aware of the number that is stamped on the tag that identifies the key and keep it in a safe location.

How do you replace a battery?

If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a clear indication that the battery should be replaced. A weak battery could cause other issues, like the check engine light coming on or the engine not cranking correctly. It is quite simple to replace the key fob batteries by using only two tools.

Before starting the process be sure that your vehicle is turned off and that all doors are shut. Locate the small metal or plastic piece on the bottom of your key fob and jiggle it until a metal key slips out. The key can be placed inside the driver door handle to unlock your car.

To replace the battery in the key fob, you must remove the rear cover. Use a pry tool to loosen the latch that holds the black negative cable. Remove the old battery, and then orient the replacement battery to ensure its "+" side faces you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position, avoiding excessive force to avoid damaging or breaking the contacts made of metal.

Once the new battery has been installed then turn the key fob off and back on in the ignition for a few times until the door locks. You can then test your kia picanto key replacement key fob to see whether it's working again.

How do you replace the smart key?

Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The difference between the two is that the smart key has a small mechanical key blade in it, whereas the standard fob does not. Both types of key fobs are equipped with batteries which eventually needs to be replaced. This is a simple procedure that takes just two minutes.

Before you start before you begin, ensure that you're on a level surface with adequate lighting and that the kia sportage key is off. Keep in mind that there are tiny pieces inside the fob which could be snagged if not vigilant.

The release button for the small size is located on the lower backside. This will be either a circular button or a rectangular slot. After pressing this button, the mechanical key blade will come out and you can then open the key fob.

Once the key fob is removed, you can remove the battery that was in it. The new battery is a C2032, and can be purchased online or in your local auto parts shop. Once you're done, your key fob should permit you to lock or unlock and start your vehicle, even if it isn't running.

How to replace the mechanical key?

The Kia key fob is a great convenience that lets us lock and unlock our vehicle with the click of one button. Like any other device, the Kia key fob can occasionally have problems. Luckily, there are ways to fix these issues and keep our key fobs in good working condition over the long haul.

A dead or weak battery is one of the most frequently encountered issues. This can cause the device to stop working entirely or work intermittently. If this happens, try replacing the battery with a new one.

If this does not solve the issue, you can use a standard flathead screwdriver to push the fob's plastic casing open. Be sure not to damage any internal components or scratch the plastic. Once the battery is opened, carefully remove the old battery and replace it with a brand new one.

Close and open the door with the mechanical key. (Every kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob to confirm it's functioning correctly. Contact a dealer or locksmith to solve the issue when the fob still is not working. To avoid a lockout in the future ensure you have an emergency key that can work in all of the trunk and door cylinders.