How to Replace a Kia Sportage Replacement Key

For a number of Kia models, the key contains the keyless entry system that is built into the key. The key is usually akin to an electronic remote and is able to be replaced with a fresh one from a Kia dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, including a dead coin battery, worn buttons signal interference, water damage and a faulty receiver module. Here are some tips on how you can get your Kia Sportage replacement key to function again.

How do you replace a remote key or smartkey

The battery inside your kia key replacement's smart key will eventually need be replaced, whether it's a remote key or a push-to-start one, or a standard metal key that doesn't contain an electronic transponder. This is especially relevant if your vehicle displays a message that indicates that the smart key or remote has a low battery.

Fortunately, it's quite simple to do. In order to replace the key fob battery remove the mechanical key from the slit on the back of the key fob. Next, break the cover. A small screw will be in the key fob, which holds the battery in the correct position. Remove the old battery by unscrewing the screw with a small screwdriver. Then insert the new one and close the hole in the key fob.

Test the key fob by pressing the lock or unlock buttons. You're good to go in case the doors lock and unlock as you expect. You can now take advantage of your Kia's hands-free lock/unlock feature whenever your fingers get chilly or you have to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming done. This requires a programing machine which is available to the locksmith in the automotive or dealer. Other keys (non transponder keys made of steel) are not required for programming. If your key requires to be programmed again, you will need to know the key code number stamped on the tag that identifies the key and then record it in a safe place.

How do I replace the battery?

If the kia picanto key fob replacement key fob does not respond when you press the lock/unlock button, it's a sign that the battery is insufficient. A battery that is not functioning properly can cause other issues, such as the check engine light coming on or the engine not turning properly. Fortunately replacing the key fob battery is a simple DIY project that requires only a few basic tools.

Make sure to shut off your vehicle and close all doors prior to beginning. Find the small metal or plastic piece on the bottom of your key fob, and play with it until a metallic key slides out. The key can be inserted into the driver door handle to unlock your car.

To replace the battery inside the key fob remove the cover that covers the rear. Use a plastic pry tool to open the latch that holds the black negative cable. Remove the old battery and align the new one so that the "+" positive side is facing your face and the "-" negative side is facing towards the fob's electrical contacts made of metal. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid bending or damaging the contacts made of metal.

Once the new battery is installed after which you turn the key fob off and then on in the ignition several times until the door locks cycle. Then you can test your Kia key fob to see whether it's functioning properly again.

How do you replace a smart key

You could have a standard keyfob or a Smart Key, based on the model of Kia Sportage. The smart key features an embedded mechanical key blade however, the standard key fob does not. Both types of key fobs are equipped with a battery inside them that will eventually need to be replaced. This is an easy process that takes less than two minutes.

Be sure to turn off your Kia, and be on a flat and well-lit surface prior to you begin. Be aware that there are tiny parts inside the fob which could be snagged if not cautious.

The small release button is located on the lower backside. It could be a circular silver button or a rectangular slot. You can open the key fob by pressing the button.

Once the key fob is opened, remove the old battery. The new battery should be a CR-2032 and can be purchased online or at a local auto parts store. After you're done, your key fob will allow you to lock or unlock and start your vehicle even if it's not running.

How to replace the mechanical key

The Kia key fob is a fantastic convenience that allows us to lock and unlock our car with the push of one button. Like all devices like a key fob, the kia Replacement key Uk can occasionally have problems. There are ways to solve these issues and keep your key fobs running for a long time.

One of the most frequently encountered problems is a low or dead battery. This can cause the fob to stop working altogether or stop working at times. If this is the case try replacing the battery with a new one.

If this doesn't solve the issue you can try using a standard flathead screwdriver to wedge open the casing of the fob's plastic. Be careful not to scratch any internal components or scratch the plastic. Once the battery is removed, replace it with a brand new battery.

Once the new battery is in, close and open the doors using the mechanical key (every Kia fob comes with an emergency mechanical key that will fit into the slot). Test the key fob to ensure that it's working properly. Contact a dealer or a locksmith to resolve the problem if the fob is still not working. Make sure they make you an emergency key that functions across all trunk and door cylinders to avoid lockouts again.