How to Replace a kia duplicate key (page) Sportage Replacement Key

For a number of Kia models keys, there is the keyless entry system that is built into the key. This key is similar to remote controls and can be exchanged by an Kia dealer.

Key fobs are prone to malfunction due to a variety of reasons, including an empty coin battery, worn buttons, signal interference, water damage and a damaged receiver module. Here are some helpful tips to help you get your kia ceed replacement key sportage replacement key to work again.

How to replace the remote key or smart key

If your Kia comes with an intelligent key, remote key push-to-start keys, or a regular non-transponder metal key the battery in these keys will eventually need replacing. This is especially true if the vehicle displays a message that indicates that the smart or remote key has a low battery.

This is a relatively easy procedure. To replace the battery of the keyfob take out your mechanical key from the slit at the back of the fob. Then, pry the cover off. A small screw is found inside the key fob to hold the battery in its place. Remove the old battery by unwinding the screw with a small screwdriver. Insert the new battery and close the opening on the key fob.

Test the key fob by pressing the lock or unlock buttons. If the doors lock and unlock according to your expectations, then you're good to go! You can now utilize the hands-free feature to lock and unlock your Kia when your fingers get chilly or when you need to run errands around Brandon.

Note: Certain key fobs may need to be programmed (transponder chips or smart keys). This requires a computer that is available only to the locksmith who works for the automotive dealer. Other keys (non transponder metal keys), do not need programming. If you want to change the programming of your key, you'll need to write down the key code's number on the tag for the key code.

How do I replace a battery

If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a signal that the battery should be replaced. A weak battery could cause other issues, such as the check engine light turning on or the engine not turning correctly. Fortunately replacing the key fob battery is a fairly simple DIY project that requires only a few tools.

Make sure that you shut off your vehicle and close all doors prior to starting. Locate the small metal or plastic piece on the bottom of your key fob, and move it until a metal key slips out. Then, you can insert the key in the door handle of the driver to unlock your car.

To replace the battery on the key fob, remove the rear cover. Use a pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and then position the new battery to ensure that its "+" side faces you and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid damaging or breaking the contacts on the metal.

After you have installed the new battery then turn the key fob off and on in the ignition until the door locks cycle. You can then test the Kia's Key fob again to confirm that it is working correctly.

How can you replace the smart key

Depending on the model of the Kia Sportage, you may have a standard key fob or a smart key. The difference between the two is that the smart key has a small mechanical key blade that is hidden inside, while the standard key fob does not. Both types of key fobs have batteries inside that will eventually need to be replaced. It's quite simple and takes just two minutes.

Make sure you turn off your Kia and be on a level and well-lit surface prior to you begin. Be aware that the fob is made up of tiny pieces that could be thrown off should you not be careful.

The small release button is located on the lower backside. It's either a circular or rectangular slot. When you press it the mechanical key blade will come out and you will be able to open the key fob.

Once you have the key fob opened then you can take off the old battery and replace it. The new battery should be a CR-2032 and can be purchased online or at a local auto parts store. After you're done, your key fob should allow you to lock and unlock your vehicle, even if it isn't running.

How do you replace a broken mechanical key

The Kia key fob is a great feature that lets us lock and unlock our car with the push of one button. Like any other device that is used, the Kia key fob can have issues at times. There are solutions to solve these issues and keep your key fobs working for many years.

A dead or low-quality battery is among the most frequently encountered issues. The battery could cause the device to stop working or work intermittently. If this is the case then try replacing the battery with a fresh new one.

If this does not resolve the issue, use a flathead screwdriver standard to wedge the fob's plastic casing open. Be careful not to damage internal components, or scratch the plastic. Once the battery is removed and replaced, you can replace it with a brand new one.

After the new battery has been put in, close and then open the doors using the mechanical key (every Kia fob comes with an emergency mechanical key that will fit into the slot). Test the key fob and ensure that it's working correctly. If the key fob isn't functioning, contact an expert locksmith or dealer to help solve the issue. Make sure they cut you an emergency key that can work across all trunk and door cylinders, to avoid lockouts again.