How to Replace a Kia Sportage Replacement Key

The key of many Kia models comes with an entry system that is keyless into. The key can be compared to the remote control and can be exchanged with a brand new one from a Kia dealer or a locksmith.

Key fobs might stop working due to a variety of reasons, such as the battery being dead, worn-out buttons, signal interference or water damage. Here are some suggestions on how to get your Kia Sportage replacement key to work again.

How to replace the remote key or smart key

It doesn't matter if your Kia comes with an intelligent key, remote key, push-to-start key, or a regular non-transponder metal key, the battery in these keys will eventually need replacement. This is especially the case if your car displays a message telling you that the smart or remote keys have low battery power.

This is a relatively simple procedure. To replace the battery on the keyfob take out your mechanical key from the slit on the back of the fob. Then, you need to pry the cover open. Inside the key fob will be an incredibly small screw that holds the battery in the correct position. By using a small screwdriver remove the screw and remove the old battery. Install the new battery and then close the gap on the key fob.

Test the key fob by pressing the lock or unlock buttons. You're good to go when the doors lock or unlock as you expect. You can now use the hands-free lock/unlock feature on your Kia whenever your fingers feel cold or you need to go on errands around Brandon.

Note: Certain key fobs could need to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If your key requires to be reprogrammed, you must be aware of the number written on the tag of the key code and then record the number in a secure place.

How do I replace a battery

If your kia picanto key fob replacement key fob isn't responding when you press the lock or unlock button on the fob, it is a sign that the battery needs to be replaced. A battery that is not functioning properly can cause other issues, like the check engine light flashing or the engine not running correctly. It is easy to replace the key fob batteries using just some tools.

Be sure to turn off your vehicle and shut the doors before you begin. Find the small metal or plastic piece that is on the bottom of your key fob, and jiggle it until a metal key pops out. This key can be put into the driver door handle to unlock your car.

To replace the battery inside the key fob, take off the cover that covers the rear. Make use of a plastic pry tool to open the latch that holds the black negative cable. Remove the old battery and then orient the replacement battery in a way that its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.

Once the new battery has been installed after which you turn the key fob off and then on in the ignition several times until the door locks cycle. Then, you can test your Kia key fob and see whether it's functioning properly again.

How do you replace a keyless keys

You could have a standard keyfob, or a Smart Key based on the model of Kia Sportage. The smart key features an embedded mechanical key blade while the standard keyfob does not. Both key fobs contain an internal battery that will eventually need to be changed. This is an easy process which takes just two minutes.

Before you begin before you begin, ensure that you are on a level surface with sufficient lighting and that the Kia is off. Also, remember that there are tiny pieces inside the fob that could fall out if not careful.

The release button for the small size is located on the lower backside. It will be either an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

Once the key fob is opened, take out the battery that was in it. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. When you are done you should be able to lock, unlock and start your car using your key fob - even if the engine isn't running!

How do you replace the mechanical key?

The Kia keyfob is a wonderful convenience which allows us to lock or unlock our car by simply pressing a button. However, like all devices it may have issues from time to time. There are methods to solve these issues and keep our key fobs in good condition over the long haul.

A low or dead battery is among the most common issues. This can cause your device to stop working or operate intermittently. If this is the case try replacing the battery with a fresh new one.

If this does not resolve the issue, use a flathead screwdriver standard to push the plastic casing of the fob open. Be sure not to damage any internal components or scratch the plastic. Once open, carefully remove the old battery and replace it with a new one.

Close and open the door with the mechanical key. (Every kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob to confirm it's working properly. Contact a dealer or locksmith to solve the issue if the fob is still not working. Make sure they cut you an emergency key that works in all the trunk and door cylinders to avoid lockouts again.