Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinctly SUV-like feel due to its larger dimensions. Moreover, the ride on 19-inch wheels in Ti and ST-L models can be a bit firm at times. The front tyres may lose grip on rough surfaces, and its CVT could occasionally exhibit wrist-flexing torque steer.

It is usually caused by a dead coin battery which can be replaced in a matter of minutes. Make sure the new battery is of the same size, voltage and specification.

Water Damage

Water damage is one of the most frequent causes for the Nissan keyfob to display the "key ID is wrong" message. The key fob is fitted with rubber seals that shield the electronic chip inside, but long-term exposure to moisture could cause it to stop working properly. It's typical to observe this if your keyfob was dropped in the water or in a swimming pool. It can also occur when it becomes wet from the rain or soapy hands.

If your key fob is exposed to water for an extended duration, it might have to be cleaned with isopropyl alcohol or electronic cleaner. It might also need to be taken to a specialist to be repaired or replaced.

If your key fob needs to be replaced, it's an easy procedure. Make sure you have the correct multipack (CR2032 3V). Open the front and back cases with the help of a small screwdriver. You'll need to remove the clips that hold the metal together and push out the battery that was in place, and then replace it with the new one. After reassembling the fob put the mechanical key back in its place and make sure it functions as intended. If it does not then you'll need to take it to a Nissan dealer or a professional auto locksmith to repair the chip in the key. The chip is typically not damaged by water and therefore should not be too expensive.

Dead Coin Battery

Another reason that your Nissan Qashqai key fob may not work is that the battery inside is dead. The batteries typically last for 3-5 years, but they are susceptible to becoming depleted over time, especially when the fob is dropped frequently. You could try replacing the battery with a new one, but make sure that it's the same voltage and size as the original. If you are using a different battery it may cause the key to have an incorrect key ID which can prevent it from pairing with your vehicle.

The most efficient method of replacing the battery on the Nissan Qashqai key fob is by opening the fob with a small flat head screwdriver. Push in the screwdriver in a small notch at the bottom of the fob, and twist gently to separate the two halves of the key fob. Remove the old CR2025 battery and replace it with a new one, making note of the position of the previous one inside the fob.

Examine the terminals to see if there is dirt or water damage prior to installing the new battery. If there is clean the terminals with the smallest amount of isopropylethanol. Make sure that the pole cables are connected correctly. They should be connected both the negative and the positive poles of your battery.

Troubleshooting

If your Nissan Qashqai's keys fob isn't working after being exposed to pure rainwater or clean tap water, this could indicate that there's a problem with the internal chip. Change the battery won't fix this, and you'll have to purchase an entirely new key fob. If the key fob stopped working after dropping it, it's likely that the chip inside was damaged. You can usually get the key fob to function again if you take it out and clean the chip using alcohol and paper towels, then put it back in.

Key ID Incorrect is a common error that you can see on the dashboard of your car. The vehicle is unable to recognize the key fob which is why it won't allow the vehicle to start. The issue can be caused by a variety of things, including water damage, undetectable malfunctions in the circuitry of the key fob or RFID interference.

The key fob won't work if the 12 volt batteries are dead or don't provide enough electric current. This can affect the remote keyless system and central locking on your nissan qashqai key replacement Qashqai, as well as making it impossible to start your engine using the key fob (if equipped with Intelligent Key). If you can't lock or unlock the door manually You should examine the batteries on the key fob to make sure they're in good shape. Try reinstalling the battery to reset your transmitter.

Reprogramming

If the key fob was not submerged into saltwater the device should be able to return to life with a simple wash of clean water. You can also clean the electronic chip with isopropyl or electronic cleaner. If none of the above works, you may have to replace the key fob.

If your nissan juke key fob Intelligent Key is still not working, there could be a problem with the connection between it and your car. To reconnect it, begin by turning the key into the ignition without starting the car. Keep doing this until you see the hazards lights flash twice. Turn the vehicle off and take away the keys.

Then, open the fob compartment in your vehicle. It is usually located on a door jamb or the handle for the driver's door. Find the small "program" button and press it. You should hear a chime sound once the process is complete.

Now that your Intelligent Key is relinked to the car It's time to test it out. You must stand a certain distance away from the vehicle, and hit all the buttons on it. If the lights flash, or the horn sounds, the key is successfully connected to the Nissan. You can also try testing it close to the Nissan.