Peugeot 208 Key Replacement

It is recommended to leave the replacement of peugeot 2008 key 208 keys to auto locksmiths who have the equipment and expertise. They will be able to create and program new keys much quicker than a dealership and at a lower cost.

If your key fob has stopped locking or unlocking your doors it could be due to a dead battery in the coin. However, there are other reasons that the key may be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your peugeot key fob reprogramming 208 from locking and unlocking, as well as making it impossible to start the engine. In this situation, you will need to employ the alternate method of starting described in your vehicle owner's manual.

Another reason why your 208 might not start is that the spark plugs are been worn down. The spark plugs ignite the fuel to start the engine. However they are limited in their life span. They'll eventually break down when they aren't used enough.

Luckily, there is an easy solution to this problem. The best option is to measure the voltage of your car battery with a multimeter. If the voltage is below 11,5 volts, it's the time to replace it. If the battery has corrosion it is essential to clean its contacts. This can be done by lifting the rubber covers covering the two terminals on the battery and using a wire brush to remove any corroded components of the battery. Then, you should reconnect the positive and negative pole cables.

Water Damage

If your 208 isn't starting and the battery isn't running, then make sure that the spark plugs work. It is possible that they are just overly dirty, causing them not to spark. This can be easily corrected by cleaning the spark plugs in an workshop.

Peugeot 308 Key Programming cars are equipped with a transponder style key that integrates with the car's immobiliser system. This ensures that only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged, it will not transmit the correct signal to the vehicle.

Water damage is the most common cause of this problem. This is especially prevalent in colder climates, where the vehicle could have been exposed to snow or rain. In this case, you need to contact an experienced locksmith who has the required tools and equipment to change the key's programming. They will also have the latest technology and equipment needed to make the Peugeot 208 smart key. The process should not take more than 15 minutes.

Contacts with the battery may be damaged.

Peugeot changed from the old carbon-encased transponder chips to an entirely new type of chip that relies on electronic components within a circuit board. The new system is excellent when it's new, however the circuit boards deteriorate over time and stop working properly.

This can prevent the immobiliser from triggering so that your vehicle won't be able to start. If this is the case, it's a good idea call a Peugeot specialist or locksmith.

A common issue is when the battery of the key fob begins to die. This causes the blade of the key to stop feeding into the lock. A car locksmith can replace the battery and cut a fresh blade for you, this is normally a quick fix.

Faulty Receiver Module

It could be that the receiver module has a problem in the event that your Peugeot key fob doesn't work after being dropped on the floor, or exposed to a sudden downpour or accidentally washed. The receiver is responsible for sending radio frequency signals to the on-board computer that controls the central locking system inside your Peugeot vehicle.

Rubber seals on the key fob block water from reaching its electronic chip. However, prolonged exposure to water may be able to penetrate these seals and cause damage to the chip. Submerging the key fob into the ocean at the beach or throwing it into the pool could be particularly damaging due to the high salt content.

If your Peugeot spare key fob isn't working You'll need the module replaced. This can only be done by a Peugeot specialist or an expert auto locksmith. In contrast to other vehicles, Peugeot keys are protected by an exclusive immobilizer system that requires the correct code in order to start the engine. It is for this reason that you should only rely on a Peugeot locksmith to design and program a replacement.

Computers with faulty on-board computers

The on-board computer of your Peugeot is responsible for many of the systems in your car, including airbags and power windows. The on-board computer displays the code when something goes wrong. This code will be saved in the system until the problem is resolved. Most often, this involves replacing the on-board computer.

One of the main causes of the light flashing is loose or corroded connections in the airbag sensor. This can be caused by wear and tear, ageing, or exposure to moisture and salt. This problem should be dealt with as soon as you can, because an airbag malfunctioning could pose danger in the event in the event of an accident.

If your peugeot 208 key fob not working is showing a card not detected error, then the battery inside the key fob might be dead or weak. This could prevent the key fob from sending a signal that disables the immobilizer on your vehicle's standard. Test this by pressing the unlock key on the key fob, and then trying to start your car. If this doesn't work, the key battery must be replaced.