How to Replace a Kia Sportage Replacement Key

For a number of Kia models, the key contains the keyless entry system that is built into the key. The key is usually akin to a remote control and can be exchanged with a new one from a Kia dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, including batteries that are dead worn buttons, signal interference, water damage, and a defective receiver module. Here are some guidelines on how to get your Kia Sportage replacement kia key key working again.

How do you replace a smartkey or remote key?

If your Kia comes with an intelligent key, remote key, push to start key, or regular metal non-transponder key The battery inside these keys will eventually need replacing. This is especially the case if your car shows a message that states the remote or smart keys aren't powered.

Fortunately, it's a relatively simple process. To replace the battery in the keyfob remove the mechanical key from the slit on the back of the fob. Then, you need to pry the cover off. Inside the key fob will be an incredibly small screw that holds the battery in the correct position. Utilizing a small screwdriver loosen the screw and pull out the old battery. Insert the new battery and then close the cut on the key fob.

Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock exactly as you expect, then you're all set! You can now use the Kia's hands-free lock/unlock feature whenever your fingers get chilly or you need to do some errands in Brandon.

Not all key fobs could need to be programmed (transponder chips or smart keys). This requires a computer that is only available to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of steel) do not require programming. If your key needs to be reprogrammed, then you will need to be aware of the key code number stamped on the tag that identifies the key and save the number in a secure place.

How to replace the battery

If your Kia key fob is not responding when you press the lock or unlock button on the fob, it is a signal that the battery needs to be replaced. A low battery may also cause other issues like the check engine light flashing on or a delay in cranking the engine. It is fairly easy to replace the key fob battery with just two tools.

Make sure that you shut off your vehicle and close all doors before you begin. Locate the small plastic piece that is on the bottom of your key fob and move it until a metal key slides out. This key can be placed inside the driver door handle to unlock your car.

To replace the key fob battery, remove the cover from the back and use a plastic bar tool to release the latch holding the black negative battery cable. Remove the old battery, and then orient the replacement battery in a way that its "+" side is facing you and the "-", negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.

After you have installed the new battery, turn the key fob off and on in the ignition until the door locks up. Then, test your Kia key fob and see if it is working properly again.

How do you replace a keyless keys

There is a possibility of having a standard keyfob, or a Smart Key depending on the model of Kia Sportage. The difference between the two is that the smart key has an incredibly small key blade tucked inside it, while the standard key fob does not. Both key fobs come with a battery that will eventually require changing. This is a straightforward process that takes just two minutes.

Before you start before you begin, make sure that you are on a flat surface with enough lighting and that the Kia is off. Be aware that there are tiny pieces inside the fob that can be snagged if not cautious.

The first step is to locate the small release button that is located on the lower backside of the fob. It's either a circular button or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open, you can simply take off the old battery and replace it. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. When you are done it should be possible to lock and unlock your car with your key fob even if the engine isn't running!

How do I replace a mechanical key

The Kia keyfob is a great convenience that allows us to lock or unlock our car simply by pressing the button. But, as with all devices there are issues with it at times. There are ways to solve these issues and keep your key fobs working for the duration of.

One of the most frequent problems is a dead or dead battery. This can cause your fob to stop working or work intermittently. If this is the case, replace the battery with a new one.

If this doesn't solve the problem then try using a normal flathead screwdriver to open the casing of the fob's plastic. Be careful not to damage any internal components or scratch the plastic. Once the battery is removed then replace it with a brand new one.

After the new battery has been put in, shut and open the doors using the mechanical key (every Kia fob comes with an emergency mechanical key that can fit in the slot). Test the key fob to make sure it is working correctly. Contact a dealer locksmith to fix the issue if the fob is still not working. Make sure they cut you an emergency key that functions for all trunk and door cylinders to prevent lockouts in the future.