How to Replace a Kia Sportage Replacement Key

The key of many Kia models comes with an electronic keyless entry system built into. This key usually resembles the remote control and is able to be replaced with a brand new one from a Kia dealer or locksmith.

Key fobs can stop working due to a variety of reasons, such as an inactive battery, worn out buttons signals, signal interference or water damage. Here are some tips to assist you in getting your Kia sportage replacement key working for good.

How do you replace a smartkey or remote key?

The battery inside your Kia's smart key will eventually require to be replaced, whether it's a remote key or a push-to-start one, or a standard metal key that is not equipped with an electronic transponder. This is particularly relevant if your vehicle displays a message indicating that the remote or smart keys aren't powered.

It's a simple procedure. To replace the battery of the keyfob remove the mechanical key from the slit that is located at the back of the fob. Then, pull the cover open. Inside the key fob there will be a small screw that holds the battery in the correct position. Using a small screwdriver, remove the screw and pull out the battery that was in place. Install the new battery and then close the slit on the key fob.

Once the key fob has new batteries check it by pressing the lock and unlock buttons. If the doors unlock and lock in the same way, you're set! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you need to complete errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) might require their programming completed. This requires a machine for programming that is available only to the automotive locksmith or dealer. Other keys (non-transponder metal keys) do not require programming. If you're required to reprogramme your key, you'll need to note the key code number on the tag for the key code.

How to replace the battery

If the kia car key replacement key fob is unable to respond to pressing the lock/unlock button, it's likely that the battery is insufficient. A weak battery could cause other issues, such as the check engine light coming on or the engine not cranking correctly. Fortunately replacing the key fob battery is a relatively easy DIY task that requires only some basic tools.

Be sure to turn off your vehicle and shut all doors prior to beginning. Find the small metal or plastic piece on the bottom of your key fob, and play with it until a metallic key slips out. Then, you can put the key into the door handle of the driver to unlock your car.

To replace the battery inside the key fob, you must remove the cover that covers the rear. Use a pry tool to loosen the latch that holds the black negative cable. Remove the old battery and then place the new battery in a way that its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid breaking or bending the steel contacts.

After installing the new battery, turn the key fob on and off in the ignition until the door locks up. You can then test the Kia's Key fob to ensure it's working properly.

How to replace the smart key?

Depending on the model of the kia keys replacement (Learn Even more) Sportage, you may have a standard key fob or a smart key. The smart key comes with an embedded mechanical key blade while the standard key fob does not. Both key fobs are equipped with an internal battery that will eventually require replacing. Fortunately, this is a fairly simple process that only takes about two minutes.

Before you start it is important to make sure that you are on a flat surface with enough lighting and that your Kia is off. Remember that the fob is made up of small parts that can fall if you're not careful.

The small release button is located on the lower backside. It will be a circular button or a rectangular slot. After pressing this button button, the mechanical blade will come out and you will be able to open the key fob.

Once the key fob is removed, you can remove the old battery. The new battery is the CR-2032, and it can be purchased through the internet or at a local auto parts store. When you are done you should be able to lock or unlock your car with your key fob even if your engine isn't running!

How do you replace a mechanical key

The Kia key fob is a great convenience that allows us to lock and unlock our vehicle with the click of an button. Like any other device it is possible that the Kia key fob can occasionally have problems. There are steps that can be taken to resolve these issues and ensure that our key fobs are in good condition in the long run.

A dead or weak battery is among the most common problems. This can cause your device to stop working or work intermittently. If this is the case, try replacing the battery with a fresh new one.

If this does not resolve the issue, you can use a standard flathead screwdriver to wedge the fob's plastic casing open. Be careful not to damage internal components, or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a new one.

Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the key fob and verify that it's working properly. Contact a dealer or locksmith to fix the issue when the fob still is not working. To avoid lockouts in the future, make sure you get an emergency key that can work in all of the trunk and door cylinders.