Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are durable, long-lasting and easy to maintain. They do not get rotten or rusty like aluminum and timber.

It is crucial to wash and oil UPVC doors and windows on a regular basis. This will help prevent costly repairs and increase energy efficiency.

1. Broken Glass

The damaged glass in your windows can cause serious damage to your home, and could even be fatal. It is important to ensure that your windows are in good condition.

For single pane windows, it can be relatively simple to replace them, and the replacement is usually able to fit into the frame that was previously installed easily. If you have double-paned windows which are held together by internal beading, it will be difficult to remove and replace the panes that were previously in use. In this instance, it is necessary to purchase plastic spacers in order to help the new pane fit into the window frame.

Wearing protective eyewear and thick gloves is a must when you are planning to remove the glass by yourself. It is also recommended to lay down a drop cloth before you start working on the glass so that any shards will fall on the fabric instead of landing on the floor, where they could be trampled on and cause further damage.

After the glass has been removed, it's a good idea to cover the gap with clear packaging tape or duct tape to block drafts and water from entering the property until a professional is able to come out and repair the window repairs near me. It also acts as a barrier to prevent any criminals from getting into your home. If the gap is particularly large, you may think about a security door window repairs that has an integrated window, as it will provide the best of both worlds.

2. Sagging

uPVC windows and doors are an affordable energy-efficient, durable and long-lasting alternative to timber windows with sash. In time, they could be affected by a variety of issues that include sagging. A sagging uPVC windows can cause problems with light, draughts and even security. If you notice that your uPVC window is beginning to shrink, it's crucial to act fast to prevent the problem from getting worse.

To repair a window that is sagging, you can try repositioning the hinges. First, you'll need to unblock the windows to get at the frame. With an screwdriver, take off the hinges on the top and bottom and adjust them by turning them clockwise or counter-clockwise. Once you've repositioned the hinges, close the window and test it for an appropriate fit. If you're happy with the fit, tighten the screws until they stay in place.

If you are unable to move the hinges, you could have to replace the seal. Rubber seals can dry out and lose their elasticity with time, which causes them to lose their tightness. If this happens, it's important to replace the seal as fast as possible so that your uPVC windows are waterproof and secure from draughts.

uPVC handles could also loosen. Most often it is due to screws that have come loose over time. However, it could be due to the fact that the handle mechanism has worn out. Luckily, it's not difficult to repair a loose uPVC window handle yourself. First, you'll need close your window and do a test to ensure that it fits. The corner joints of the sash need to align with the casing joint. If it does not, you can use the screwdriver to loosen up the handle. Then turn the mechanism to position.

3. Water Leaks

If you wake up to damp floors and mouldy walls every time it rains it's important to take action. The leaks of water from windows do are not just a cause for destruction of your home's structure but also hamper your efforts to regulate the temperature within your home. The most common cause for leaking uPVC windows is that the sealant around the frame has been damaged or not present.

It is a fairly easy fix and should be undertaken by any skilled DIYer. Depending on the severity of the issue the caulking that was used up may require removal before a new layer of caulk can be applied. It is important to remember that when it comes to uPVC window repairs, do avoid the temptation to "over-caulk and then make the area more difficult to clean and can reduce the efficiency of your energy.

Verify that the drainage holes do not have debris in them, and also ensure that the sill pan has been properly angled to drain away from the window. In more serious situations, you might need to consider replacing the window.

Other indicators of long-term water leakage are rotted sills and the appearance of black spots of mold on the wall near the window. This fungus thrives in conditions of dampness and can spread quickly throughout the house.

It is also important to keep in mind that if the leakage is coming from between the glass of your double-glazed windows it may be more likely to be a problem with the glass seal rather than the frame or sagging. This can be easily fixed by an uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges may be to blame for the reason that your uPVC window is difficult to open or it opens in a breeze. They can be repaired by any skilled DIYer and can be completed in just a few minutes.

Like all mechanical parts hinges are prone to be damaged over time. It's easy to change the hinges on a window but it's much simpler if you have someone to help you hold the frame.

Make sure that the uPVC hinges are closed and open in the correct direction. You can do this by looking for the arrow on each hinge. This indicates which way the window should open.

The problem can be caused either by opening the window incorrectly or due to a poor installation in the factory. Sending us photos via our website is often enough to resolve the problem. We are always happy to give suggestions.

Regularly lubricating hinges is also essential. Applying a light engineering lubricant on the hinges is a good way to do this. We recommend using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It can also prevent corrosion and reduce the risk of sticking. The ideal time to perform this every year. WD40 and other solvent based oils are not recommended because they can damage the parts of your uPVC window.

5. Draughts

Draughts can be caused by different things. The hinges may also become unbalanced due to wear, causing an opening where the sash meets frame. If they're beyond repair, it may be required to realign them. The interlock may also become unbalanced. This is located on the hinge side and might require to be cleaned. In some cases, it may be necessary to replace the hinges.

These seals are susceptible to wear and tear or become damaged over time, allowing air escape. Replacing these with high-quality weatherstripping is a good way to keep draughts at bay. Another alternative is to replace the window with low-emissivity glass. which will help regulate indoor temperatures, and also lessen the possibility of draughts.

Another method of reducing drafts effectively is to use a Draught-exclusion device. These are usually made of fabric tubes filled with a filler that can be put on top of your window sill. These will keep your home warm by blocking out cold air.

Your windows made of upvc will remain a great source of insulation and security in your home with regular maintenance and repairs. It is crucial to realize that all windows have a life span and there may come an point at which it is more economical to replace them than fix them. If you have any problems with your Upvc window it is recommended to speak with a professional immediately.