Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are easy to maintain and durable, as well as long-lasting. As opposed to aluminium and timber they do not corrosion or rot.

It is important to clean and oil UPVC doors and windows on a regular basis. This will help prevent costly repairs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows could cause serious damage to your home and even be fatal. It is important to ensure that your windows are in good shape.

For single pane windows it is relatively easy to replace windows, and the new one will usually fit inside the frame of the previous one easily. However when windows with double panes are anchored by internal beading it will be more difficult to take out the panes that are in place and replace them with new ones. In this situation it is essential to purchase plastic spacers to aid in fitting the new pane into the window frame.

If you are going attempt to remove the window panes yourself it is crucial to wear the proper safety gear such as gloves that are thick and eye protection. You should also lay down a dropcloth prior to you begin working on the window panes to ensure that any shards fall on the fabric and not onto the floor which could cause them to be trampled under.

It's a great idea tape the gap once the glass has been removed. This will stop drafts and water from entering your home until a professional is able to repair the window. This will also act as a barrier, deterring any intruders from getting access to your home. If the gap is large, you may want to consider using an alarm Door Repair (intranet.welfarebox.com) that comes with an integrated window, since it offers the best of both worlds.

2. Sagging

uPVC is a durable energy-efficient, cost-effective and economical alternative to timber sash windows. However, over time, they are susceptible to a range of problems including sagging. A sagging uPVC windows can cause issues with light, draughts, and even security. It's crucial to act as soon as you discover that your uPVC windows are sagging.

To fix a sagging window you can try to reposition the hinges. You'll first need to open the windows to reach the frame. After that, using the screwdriver, you'll be able to take off the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. Once you've adjusted the hinges, shut your window and check for fitting. If you're satisfied with the fit, you can tighten the screws to ensure they stay in the right place.

If you can't reposition the hinges you may require replacing the seal. Seals made of rubber can dry out and lose their elasticity with time, leading them to loosen. It is essential to replace your seal as quickly as you can in order to keep your uPVC window waterproof and draughtproof.

uPVC handles could also become loose. This is often caused by screws that have been removed over time, but it can also be due to the mechanism of the handle getting worn out. It's fairly simple to fix a loose uPVC handle. First, you'll need close the window and then perform a test fit. The corner joints of the sash should be aligned with the casing joint. If it doesn't then you can make use of a screwdriver to loosen the handle, and then return the mechanism to its original the position it was in.

3. Water Leaks

It is essential to take action if get up each morning to find mouldy walls and wet floors. The leaks of water from windows do are not just a cause for degradation of your home's structure but also undermine your efforts to regulate the temperature within your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

This is a fairly simple fix that can be completed by any competent DIYer. Based on the severity of the problem the old caulking may need to be removed before a new layer can be put on. When it comes to uPVC repair, it is important to avoid 'over-caulking'. This will only make your window more difficult to clean and reduce its energy efficiency.

It is important to check that the drainage holes are free of debris and that the sill pan has been angled in a way that allows it to drain away from the window. In more serious cases you might have to consider replacing the window.

Mold spots and rotted sills are also signs of water leakage. This fungus thrives in humid conditions and can propagate quickly throughout the house.

It is also important to note that if the leakage is coming from between the glass in your double glazing near me glazed windows, it is more likely to be a problem with the glass seal, rather than the frame or sliding. A uPVC specialist can easily solve this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges could be at fault for the reason that your uPVC window is difficult to open or it blows open with an ease. These are easily repaired by any DIYer who is skilled and are usually done within a few minutes.

Like any mechanical part hinges will be damaged over time. It's very simple to replace a hinge on a window but it's much easier if someone helps you hold the frame.

Make sure that the uPVC hinges open and close in the proper direction. You can check this by checking for the arrows on each hinge, this indicates the direction in which the window should be opened.

The problem with the hinges on windows could be the result of incorrectly opening the window in a certain way or by poor installation at the factory. Sending us a photo via our website is often enough to resolve the problem. We are always happy to offer suggestions.

It is also crucial to lubricate the hinges regularly. This can be done by applying a light engineering oil on the hinges. We recommend using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regular lubrication can allow the window to open and close more easily. It also decreases the chance of windows sticking and help prevent corrosion. This is recommended to be done at least every year. WD40 and other solvent based oils are not recommended because they could damage parts of your uPVC window.

5. Draughts

Draughts in windows made of upvc can be caused by different things. Firstly the hinges, again because of wear and tear, can become misaligned, this can cause gaps to develop where the sash joins the frame. If they are beyond repair, it might be necessary to get them re-aligned. In addition, the interlock could also become misaligned. This is located on the hinge's side and might require to be cleaned. In certain instances it is possible to replace them.

The next most common reason for draughts are the window seals. They are susceptible to being worn out or damaged over time, and will allow air to escape through these gaps. Replacing these with high-quality weatherstripping is a good way to keep draughts at bay. Another alternative is to replace the window with low-emissivity glass, this will help in regulating indoor temperatures, and also reduce draughts.

The final method to cut down on the amount of draughts is to use a Draught-exclusion device. These are usually fabric tubes filled with a filler that can be placed over your window sill. These will help to block out cold air and keep your home warm and cosy!

Your windows made of upvc will remain a great source of insulation and security in your home with regular maintenance and repairs. It is important to remember that all windows eventually wear out and it may be cheaper to replace them than to repair them. If you are experiencing problems with your upvc windows, it is always best to seek professional assistance as soon as possible.