UPVC Window Handle Replacement

Replacing a broken window handle is a simple process and with the right tools it can be accomplished quite quickly. It is important to know the type of handle you have and the spindle's size before purchasing an alternative.

Older uPVC windows feature handles with cockspurs, which have spurs that protrude to lock over a cockspur wedge striker plate. They can be right or left-handed and have to be replaced with the same handle.

What type of lock and handle do I have?

There are many upvc window locks and handles each with its own advantages and purposes. The type of handle that you have will determine whether or not your locking mechanism is effective and if it's easy to open the windows. With time and regular use, window handles made of upvc are prone to wear or damage. out, rendering them less secure and effective. In some cases they may even fall off completely. If you find that your window handles have fallen off, it's crucial to fix them as soon as you can. This will prevent possible break-ins, and keep your house safe.

Luckily, replacing your window handles made of plastic is a relatively simple task that can be completed by almost everyone. With just a few tools and the right information it's a simple process that shouldn't take longer than a couple of minutes. To begin you must determine the type of lock and handle you have on your window made of upvc and then find the perfect replacement.

Inline Espagnolette Handles

These are the most common type of upvc handles and are usually located on the side of your window. They are flat in design and feature a latch that engages with the locking mechanism of the window frame when turned. Inline upvc handles have a spindle that goes through the center of the handle, and into the frame of the window to operate the latch.

Cockspur Handles

They are typically found on older uPVC window frames and have a distinctive, hook-shaped design. Cockspur handles are attached to the frame of the window by a single screw and are less secure than other types of window handles.

Tilt and repairmywindowsanddoors Turn Handles

Unlike the other handles made of upvc the tilt and turn handles can be turned to open the windows and repairmywindowsanddoors the handle can be tilted to the side for ventilation. They have a 7mm spindle in the back and are available both in right-hand and left-hand versions.

It is essential to know the size of the spindle when purchasing a replacement handles made of upvc. There are a few that are exactly the same size. Drop something in the middle of the hole to measure the length. This is the length of the spindle that will be suitable for your window.

What is spindles?

uPVC window handles operate in a similar manner like doors. By turning the handle, you are able to activate a latch inside the frame. This unlocks the window to allow it to be closed and opened. However, sometimes the handles may become damaged, especially when they are frequently used or exposed to extreme weather conditions. You may need to replace the handles on your uPVC window if they are not operating correctly.

There are many different kinds of uPVC handles that are available, including Espag, Cockspur and Spaded handle options. They are designed to fit into the uPVC frames in different ways. Each handle utilizes a specific spindle to lock the mechanism fitted to the window. This is why it is essential to know the type of handle you have on your uPVC window so you can get the correct replacement windows near me for it.

The base of the handle will inform you what type of uPVC it is. A snap-in cover should be over the screw that holds the base of the handle in position. Take it off and you should be able see the second screw at the opposite end of the base portion of the handle. Once both screws are removed you should be capable of pulling the handle away from the uPVC window.

After taking off the uPVC handle, carefully remove it from the locking mechanism. Take note of the length of the spindle. You'll need to purchase a replacement with the same length as the handle that was originally used and the locking device.

The spindle wears out and is unable to operate the locking mechanism. This can be due to damage caused by constant use, a loosening of the locking mechanism, or even corrosion that occurs over time. If this happens, it will be necessary to replace the window handle as well as the locking mechanism to restore full functionality to your uPVC windows.

How do I take off my old handle?

Over time and through everyday usage, window handles could become damaged or broken and if this happens, it is crucial to repair them as quickly as possible to ensure the safety of your home. It is easy to replace a damaged or worn handle. The task can be completed in under an hour without the need of special tools.

To take off the handle, first remove the screw at the bottom of the handle. Once the screw has been removed, the handle will be pulled away. There will be another screw located at the bottom of the handle base, and it can be removed too. Once the two screws are removed, the handle can be removed from the base of the window.

After the handle has been removed, grab the new handle and line up the fixing holes with the holes present in the window frame. If there is a sticker or cap on the new handle, remove it if required and screw the handle into the appropriate position. Once the handle is in place, it is crucial to verify that it works by turning the handle and making sure that the lock mechanism is activated.

Espag handles have a spindle that protrudes from the handle and slot into a multipoint locking mechanism in the frame of the window. Cadenza windows have a blade with cutouts that fit into the lock mechanism. Cockspur handles are long and hang over the outer frame of the window or the transom bar crossmember.

Once you have the new handle in place, you can insert the spindle into the lock in the window and then tighten it down. Replace the snap-in cover and screw cap (if applicable) after the handle has been firmly fixed. The handle is now ready for use, so try opening and closing the window a few times to make sure that it functions well and securely.

How do I install the new handle?

It's not that difficult to change the handle on your windows made of uPVC. The procedure is easy. You'll need an screwdriver and a bit of patience. First, make sure that the handle that you are replacing is unlocked. Then remove any screws visible. You can also replace them with screw caps. After you have removed the handle, you will need to note the length of the spindle that extends from the back. This is vital as it will determine what kind of handle to buy.

Espagnolette handles are the most common type of handle for uPVC windows. They have a spindle that is connected to the handle and acts as a locking mechanism inside the window frame. Once the handle is turned it opens the latch on the window and allows it to open. Over time and through regular use, espagnolette handles may be damaged or damaged and it is necessary to locate replacements.

Cadenza handles are a form of uPVC handle that is usually used with tilt and turn windows. They feature an extended blade that works an interlocking mechanism that is multipoint within the window. They are usually more secure than espagnolette handles as they can only be opened from the inside. They can be replaced with the same procedure as espagnolette handles however you will need to ensure that the new handle has an angled blade instead of a flat one.

After you have picked the right handle, simply align the new handle with existing screw holes before screwing it into place. Then, put the screws back on and make sure the new handle functions correctly. You can do this by dragging the handle between the locked position to the unlocked one several times. If you experience any issues, it could be beneficial to speak with a professional to determine if they can assist in resolving the issue. They are often able to advise you on the best solution to solve the issue in a speedy and efficient way.