Reasons Your fiat doblo key fob replacement, pop over to this web-site, 500 Key Fob Won't Work

A key fob from fiat 500 key fob 500 makes it easy to open doors and start your vehicle. There are many reasons the fob may stop working. It could be due to a dead battery, damaged receiver module, water damage issues, and interfering.

This listing is for an NEW replacement Fiat Flip Key Remote that looks like the Ilco brand. It has to be professionally programmed (click here to find local locksmiths for your vehicle). It comes with trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob not working. Modern key fobs come with a limited operating range and should be within some feet of the vehicle in order to function. If you're not close to your vehicle, and you press the key fob button the car won't respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the coin-cell battery (Part Number CR2032) with a new battery of a reputable brand such as Panasonic Duracell or Energizer. You can find them at the local hardware store or on the internet.

You can test the battery on your coin-cell by pressing the buttons while you're standing close to your fiat 500 key fob 500. The parking lights should light up and the key fob will operate the lock and unlock switches.

If the fob's key doesn't work after replacing the battery, it might have water damage that stops it from connecting to the receiver module in your car. Water damage can occur in a number of ways, from small splashes to submerging the fob in salt water at the beach. If you think your fob was exposed to water, place it in a bag of rice to draw out the moisture. If this fails, you'll have to get your fob changed by an auto locksmith or dealer.

Water Damage

Water damage can happen if you immerse the fob into the ocean, or wash it in a washing machine. Saltwater can cause the circuit board to short, and eventually die. It's not a good idea to submerge the fob in water, but don't give it up when you accidentally drop it in the water or don't remove it from your pocket.

First remove the battery from the fob. Before replacing the battery, clean the electronic chip with isopropyl or another similar product. Check the fob again to determine if it's working. If the fob doesn't work, it may need to be programmed again. This is usually done by an auto locksmith or dealer.

If your key is a bit older and has not been programmed to work with your vehicle then you'll need to replace it completely. A professional locksmith in the automotive industry can complete this simple process. The locksmith will have to cut the key to match the ignition on your vehicle. They'll also need to reprogram the fob in the system of your car. This is an affordable and quick process that can be completed on the same day.

Receiver Module Issues

Your 500 key fob may not work because it's out of range. The remote usually has an area of 30 feet or less, and if it's too far from your vehicle, it will not respond to your commands. It is possible to solve this issue by moving the remote closer to your vehicle until it responds.

If you've replaced the battery in your coin (commonly called"button" or "button" or "watch") and the fob isn't working, it could have an internal circuit board problem. In most cases, reprogramming the fob can resolve the issue. You can find the steps for most vehicles on YouTube or in the owner's guide.

You may need to replace the metal retaining clips that hold the coin battery in place. If they lose tension it could prevent your coin battery from being properly seated and cause your remote to malfunction.

In rare cases the fob could be out of sync with your vehicle because of hardware or software problems. This can cause a major issue, but you are able to often fix this by visiting a local dealer or auto locksmith to reprogram your fob for you. In some cases the software might need to be reinstalled in your body control modules.

Interference

Interference can also cause the key fob not to receive or transmit the signal. This may happen if the keyfob's location is in close proximity to a radio transmitter such as a cell phone or radar detector. The key fob could not function due to a bad connection to the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you have tried everything at home to resolve it (e.g. You may have a faulty 500 receiver module if you've tried replacing the battery, reprogramming it, or using a spare key fob. The receiver module is situated under the dash and picks up the radio frequency signals from the key fob. It transforms the signals into electronic commands which are then interpreted by the vehicle.

Luckily, there is an easy way to reset all on-board systems in your 500 and include the key fob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Reconnect the battery. This will eliminate any remaining electricity and restart the car's computer system, which could allow you to get your key fob working again. If the problem persists you should speak with an expert technician. They'll be able to identify the root cause of your issues.