Peugeot 3008 Key Fob Problems

The mid-sized SUV from Peugeot, the 3008, has plenty of positive attributes. It's stylish, handles well and has a large boot. But is it able to beat off strong competition in the most crowded area of the market?

If your Peugeot keyfob doesn't work it is possible that it was exposed to clean or soapy tap water. It is possible to take off the battery and clean it with electronic cleaner or isopropyl alcohol.

Dead coin battery

peugeot spare key key fobs have a small coin battery that powers their remote locking and other functions. The battery has a short life span and may be worn out after a long period of use. Voltage testing is a straightforward method of determining if the battery is in a bad state. Multimeters are used to measure voltage between the plus and minus poles of the battery. This test will reveal if the battery is dead.

The receiver module may be the reason why your key fobs not working after having used your Peugeot 3008 for a long time. The receiver module is responsible for receiving radio frequency signals from the key fobs and transferring them to the vehicle's systems. If the receiver module is defective, it will not be able to transmit commands to other modules of the vehicle.

Another common reason for a non-working key fob is moisture or sweat on the circuit board. This can result in short circuits that draw the battery out and also disable the remote locking feature of the fob. If this happens you must take your key fob to a technician that specializes in chip level repairs.

Water damage

Water damage can cause problems regardless of whether you dropped your keyfob in the pool in the pool, washed it off or left it in the rain. Water is a good conductor, and can damage circuit boards. It can also cause corrosion to the metal trace on the key fob as well as other components. A wet circuit could cause batteries to lose their charge.

If you have a spare key fob, try using it to unlock or lock your Peugeot 3008 to eliminate the possibility that a dead coin battery is the cause of the problem. Interference signals can also cause your key fob to stop working properly. These interfere with the signal sent by the receiver module. These interference signals are triggered by a variety of sources, including radio transmitters within the vicinity.

If you hear sloshing sounds emanating from your Peugeot 3008 when driving, this is likely due to a clogged condensate drain for the evaporator. You can test this by blowing compressed air through the drain holes under your door. You can also use a flexible metal wire for wriggling drain holes to clean any dirt that has accumulated. Air pockets can be identified by sloshing sound.

The receiver module is not working properly.

The receiver module on the Peugeot 3008 key fob is responsible for transmitting the remote keyless system signal from the key fob to the car's receiver. If the receiver module is damaged, it may hinder the car's ability to recognize the key fob. Other factors that can trigger this issue are an unresponsive battery water damage or interference from electronic devices that operate at the same frequency as the key fob. In these situations there may be a message saying "card not detected" may be displayed on the display.

Fortunately, there are several ways to troubleshoot this issue. Try replacing the battery or reprogram the key fob. You can also make use of a spare key to start the car. However, if the fob isn't working even after these steps, it might have a chip that's defective.

It is best to remove the chip and clean it using paper towels and rubbing alcohol. If the chip has been damaged, it is recommended to buy a new one. FB Series enclosures are designed to fit a key fob and come with a coin cell battery holder that fits the most popular type of key fob batteries. They can also be personalized with digital printing and CNC cutouts that are machined. If your key fob was exposed to dirty or salted tap water, it's possible that the chip has become infected.

Keyless entry systems with malfunctions

If you are seeing "card not detected" This means that your car is unable to receive a signal sent by your key fob. This could be due to many reasons like batteries that are weak or dead. The problem can often be solved by pressing the start button on the key fob. In some cases, you'll require taking the keyfob to a Peugeot dealer for further repairs.

The first step to fix the problem with a Peugeot 3008 key fob that isn't able to unlock or lock the doors is to check its battery. Batteries are typically the cause of a malfunctioning key fob. However, there are also other causes that could be involved. They include worn buttons, damage to the receiver module, water problems, and signal interference.

If you've recently experienced the Peugeot key fob exposed to water that is clean, it's a good idea to remove the battery and dry the electronic components with paper towels. You can also try isopropyl alcohol or an appropriate cleaner for this. It is recommended to replace the fob if it's been exposed to salt or soapy water.

If your key fob still not working, try to reset it by disconnecting the battery that is 12 volts for approximately 15 minutes. Then, reconnect the negative cable first, then followed by the positive cable.