Fiat 500 Replacement Key Fob

It may be time to change the battery if your 500 remote key fob is not working. If you replace the battery but it doesn't work it could be the issue elsewhere.

At United Locksmith, we specialize in the creation of new keys for old automobiles. We have the tools and parts needed for this service.

Dead Coin Battery

The most common reason your Fiat 500 key fob will not lock or unlock the doors is a dead battery. The key fob comes with the battery of a coin-cell that can quickly deplete when it isn't utilized frequently enough. If your remote is beginning to show signs like a loss in range or stopped functioning, then the battery may be dead.

The battery inside the key fob is held in place with metal clips that retain it. If the clips aren't secure, they can cause contact issues which will prevent your remote from receiving power. Make use of a flathead screwdriver to break open the retaining clip and remove the battery. Make sure you use an identical replacement battery kind of voltage, the same size, and specification as the original battery.

Water exposure can cause the key fob to become corroded or damaged. Even a short bath in soapy water could cause damage to the electronic chip inside. It is best to keep your key fob in a dry place.

Water Damage

Damage to your water supply could be the cause of your key fob not functioning properly. The rubber seals on key fobs keep them from being damaged by a light splash or drizzle of water. However, it is important to keep the car keys away from the washing machine, the ocean, and pool.

The key fob comes with an electronic chip that transmits an electronic message to the immobilizer system in your car. The chip allows the 500 to lock and start. If it gets wet, however it won't function.

If you want to check whether your key fob still working it is possible to clean the internal electronics using isopropyl or electronic cleaner. It is recommended to replace a key fob in the event that it has been submerged into salt water, rather than trying to fix it yourself.

While a replacement fob can cost a little money, it's far less expensive than having to pay for your Fiat 500 to be towed to the dealer for repair! You can also do it yourself by following just a few steps. Make sure you have the correct type of battery before you attempt to open your key fob. This task is much simpler than it appears and you can find step-by-step instructions on the internet for nearly any car key fob.

Faulty Chip

The chip in the key fob communicates with the immobiliser in your vehicle to ensure that the vehicle will only start once the proper keys are inserted. If the chip is damaged, or corrupted in any way it will not start.

A faulty chip can occur due to many reasons, but the most common reason is water damage or an unresponsive battery. Whatever the reason, it's best to delegate the job to a locksmith who can replace the chip for you swiftly and at a cost-effective price.

If your key fob stops working after exposure to clean water from the tap or rain, take off the battery and wipe down the electronic component with a paper towel to ensure it is fully dry before putting it back in. If the key fob does not work it's likely to be to be a damaged chip and is required to be replaced.

Many people will seek out their dealer when in need of a new Fiat key fob, however it can be a expensive option. If you are looking for a low-cost solution to have your Fiat key fob repaired make sure you contact United Locksmith. We have all the tools and experience needed to repair your fiat 500 replacement key fob quickly and professionally. way.

Faulty Receiver Module

Fiat key fobs send signals of up 50 feet away to the vehicle, which will unlock and close the doors (and start the vehicle for vehicles with automatic transmissions). There are several reasons why the fob may stop working. This could be due to a dead coin battery damaged by water or worn buttons or a problem with the receiver module, and signal interference or a malfunctioning electronic chip.

If the fob was in the pocket that has been subject to severe trauma (such as being dropped on the floor or washed in the washer) the fob may not be in a position to connect with the Body Control Module (BCM) of the vehicle. The BCM is a security system that will only accept signals from genuine original keys.

If this is the case, then you have to replace your fob. A professional locksmith is able to handle all aspects of the key replacement process and even program a new one for the 500. They can even provide you with an clone fob that performs exactly the same way as the original (and costs only one-third of what it would cost).