Replace Nissan Key Fob Batteries

If your Nissan keyfob isn't responding to your commands, then its battery may be dead. It's an easy fix that most people can fix themselves.

If you want to change the battery, you can purchase the new one from a hardware shop or consult the owner's manual for the model you own.

Changing the Battery

The key fob of your Nissan model has a lithium battery built-in that eventually loses its charge. Fortunately, replacing the battery on the key fob is a simple procedure that takes just a few minutes to complete. First, you'll need to purchase an CR2032 replacement nissan key fob battery. This is a small coin cell battery that is commonly used in key fobs, and it can be found in most convenience stores. To open the key fob, you'll also require an appropriate pair (latex or not) of gloves as well as an incredibly small screwdriver. Before beginning, be certain to read the owner's manual to find specific steps and instructions.

When you have the new battery, you can remove the old one by turning the fob on its side and looking at the back side. You will see a small catch that you need to release by pulling it down. This will take the mechanical key from its original position within the fob.

Install the new battery and ensure it is properly positioned. Once the battery is in place then close the fob and then click the two sides together. Test your key fob after completing this step by pressing the unlock button. If everything is in good and in good working order, you're ready to enjoy your nissan juke key fob replacement's many features. After replacing the battery, it's recommended to re-program your key fob to ensure that it's working properly.

Replace the Transmitter

With your key fob functioning as the "key" to many of your car's key functions, it can be a serious blow should you lose or break it. A damaged or malfunctioning key fob could prevent you from locking and starting your vehicle.

Therefore, it's a smart idea to have an extra key fob in your possession in case of an emergency. The procedure for replacing your Nissan keyfob can be done in a relatively straightforward manner. The process of replacing your Nissan key fob is quite easy. You'll need an additional flathead screwdriver as well as the new battery to get rid of the old.

You'll require a round Panasonic CR 2032 3V battery (you can usually find them in multipacks, for less than $5 USD). The battery is situated in the back half of the key fob. You'll need a small screwdriver with a flat head to gently split the two halves. Use a small flathead screwdriver to lever the clip that is located at the top of the battery and pop it out, taking note of its position. Replace the battery, and then put it back together to form the key fob. Make sure to test it to verify it is working.

Nissan Intelligent Keys will eventually get worn out and need to be replaced as with any other electronic device. To help you avoid this issue, it's a good idea to shield your key fob from magnetic fields, water, and physical impacts Be careful not to drop it or place too much pressure on it.

Replace the Key

If your Nissan key fob goes out and you are unable to use it to unlock your car or start it. That's a problem for people who have to travel to work in Detroit, run errands near Dearborn, or go out for a night on the town close to Troy.

It's not too difficult to replace the battery in your Nissan Smart Key. You can do it at home or at the dealership, and you'll usually find a set for less than $5 at a hardware store.

Flip the fob back and push the small catch at the back. This will release the emergency mechanical key within. The emergency key will not allow you to start your vehicle however, it will allow you to open the door.

Then look for a tiny gap on the top of the key fob casing. You can use a screwdriver to pry out the two pieces of the key fob. Once you've accessed the internal battery, you can remove it and note its position. When you are ready to reassemble your key fob, insert the new battery and then snap the two pieces of the case back together. Insert the mechanical key and your Nissan smartkey will work like a normal key.

Other Issues

Many modern vehicles are equipped with key fobs that allow the user to lock and start them without using a physical car key. To accomplish this the key fob utilizes a small transmitter to communicate with the car's computer system.

There are many possible reasons that your Nissan key fob will not work after you replace the battery. One possibility is that the new battery was not properly placed into the key fob. A reset of the key fob is a different possibility. This is a simple process which you can carry out at home with a few simple tools.

You'll need, for instance an screwdriver with a flat-headed tip to take out the old battery from the key fob. Then, you can use a screwdriver to open the back of the key fob to insert the new battery. After that, you'll need to reset the key fob so it works with your vehicle.

You can easily program your Nissan key fob by yourself, as they are all user-programmable. It is usually done by inserting the key fob in the ignition twice in five seconds. If this doesn't work, you can bring your key fob to a dealer or auto locksmith to get it programmed. The cost will depend on the person you speak to and the type of vehicle you own.