How to Replace a Kia Sportage Replacement Key

For a variety of Kia models keys, the key has a keyless entry system built-in. This key is similar to a remote control and can be exchanged by a Kia dealer.

Key fobs might stop working for a variety of reasons, such as the battery of the coin is dead worn buttons, signal interference, water damage, and a defective receiver module. Here are some suggestions on how to get your Kia Sportage replacement key back to working.

How to replace a remote key or smartkey

The battery inside your Kia's smart key will eventually have to be replaced, regardless of whether it's a remote as well as a push-to start key or a regular key that is not equipped with a transponder. This is particularly true if the car displays a message indicating that the remote or smart key has low battery power.

It's a simple process. To replace the battery on the keyfob take out your mechanical key from the slit at the back of the fob. Then, push the cover off. Inside the key fob there will be tiny screws that hold the battery in its place. Using a small screwdriver, loosen the screw and remove the old battery. Insert the new battery and close the gap on the key fob.

When the key fob is equipped with a fresh battery and you've tested it, press the locks and unlock buttons. It's good if the doors lock and unlock as you expect. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers feel cold or when you need to run errands around Brandon.

Not all keys may require to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or automotive locksmith can access. Other keys (non-transponder metal keys) do not require programming. If you need to reprogramme your key, you'll need write down the key code's number on the key code tag.

How do you replace a battery?

If the Kia key fob is unable to respond when you press the lock/unlock button, it's likely that the battery is low. A low battery may cause other issues, like the check engine light turning on or the engine not running correctly. Fortunately replacing the key fob battery is a relatively simple DIY project that requires only a few tools.

Be sure to turn off your vehicle and shut the doors before you begin. Locate the small metal or plastic piece that is on the bottom of your key fob, and gently jiggle it until the metal key is released. Then, you can insert the key in the handle of the door for the driver to open your car.

To replace the key fob's battery, remove the cover from the back and use a plastic bar tool to loosen the latch holding the black negative battery cable. Remove the old battery and align the new one so that the "+" positive side faces you, and the "negative" negative side is facing the fob's electrical contacts made of metal. Avoid using too much force when pushing the new CR2032 into place to avoid breaking or bending the steel contacts.

Once the new battery has been installed and the key fob is turned on, turn it off and then on in the ignition for a few times until the door locks. You can then test the kia picanto car key replacement's key fob once more to ensure it's functioning properly.

How to replace a smart keys

Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key. The smart key is equipped with an embedded mechanical key blade, however, the standard key fob does not. Both key fobs are equipped with batteries that eventually require replacement. Fortunately, it's an easy process that takes just two minutes.

Be sure to switch off your Kia, and be on a level, well-lit surface before you begin. Keep in mind that there are small parts inside the fob that could fall out if you are not cautious.

The first step is to locate the small release button that is located on the lower backside of your fob. It's either an oval or circular slot. Once you press this button, the mechanical blade will come out and you will be able to open the key fob.

Once the key fob is removed, you can remove the old battery. The new battery is a CR-2032 that can be bought online or from your local auto parts store. After you're done, your key fob should be able to lock the vehicle, unlock it, and then start your vehicle even if it's not running.

How do you replace the mechanical key?

The Kia keyfob is a great convenience that allows us to lock or unlock our car by simply pressing a button. As with all devices, the Kia key fob may have issues. Luckily, there are steps that can be taken to solve these issues and ensure that our key fobs are in good condition in the long run.

One of the most frequently encountered issues is a low or dead battery. This could cause the fob to stop working completely or even to stop working intermittently. If this is the case then replace the battery with an entirely new battery.

If this isn't enough to solve the issue, try using the flathead screwdriver that is standard to wedge the fob's plastic casing open. Be sure not to damage any internal components, or scratch the plastic. After the battery has been removed and replaced, you can replace it with a new one.

Once the new battery is installed, close and unlock the doors with the mechanical key (every key fob in the kia has an emergency mechanical key that can fit into the slot). Test the key fob and verify that it's working correctly. If the key fob isn't functioning, contact a dealer or locksmith to help resolve the issue. To avoid future lockouts, make sure you get an emergency key that will work on all trunk and door cylinders.