How to Change a subaru key fobs Spare Key

If you lose your subaru impreza key car key, call a locksmith. Usually, they will cut an alternative key for you at a lower cost than the dealer.

subaru remote key replacement car keys are usually either intelligent "push-to-start" fob remote keys or simple keys made of metal. The Fob key has to have its chip reprogrammed.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your car or the lift gate. These remotes function with keys inside your car to communicate with the computer system of your vehicle.

Subaru models include a less known feature called PIN Code Access. You can utilize a personalized number sequence to start and open your vehicle. If you own a more recent Subaru Forester, Outback, Crosstrek, WRX, WRX STI or Impreza that comes with this feature, consult your owner's guide to find out how to use it.

It's possible that the battery in the key fob has failed. You can check the battery life of your key fob by using a portable tester or a multimeter you can find in your garage.

The next step is to remove the key fob from its case, and then examine its transmitter circuit board. This board will have one or two sets of 8-digit numbers, so jot down the first set so you will be able to remember it later. Once you've finished then put the key fob back together and you'll be able to program it at home. This procedure differs based on the year and model of your car. However, it is usually simple enough to complete yourself.

Key Fobs

subaru key car's newest models feature key fobs which not only unlock doors, but also turn on lights, lock the gas cap, and even start the car. That last trick is especially useful if you've ever parked at the gas pump only to find that your car isn't starting because the battery in the key fob was dead.

No matter if your Subaru is new or older it's likely that your key fob is able to be replaced with minimal difficulty. It's important that you remember that more recent models with the highest level of technological advancement may require an excursion to the dealer. With little effort and some time, you can build your own key fob replacement.

Start by opening the case and examining the circuit board of the transmitter. (Instructions on opening the case are usually given in the owner's guide). There should be one or two serial numbers of 8 numbers each. Keep the first set of numbers in your wallet for later information.

After that, get in the driver's seat and close all of the doors. Turn the key 10 times to start your car, then switch it off. Press the lock button on the key fob, then open the door to verify that your doors are functioning properly. Close the door, then remove the key. The car should chime again, indicating that the key fob has been programmed.

Ignition System

If your Subaru keys aren't functioning as they ought to, it could be due to the fact that the battery is dead. If you have the knowledge, you can replace the battery of your key fob yourself. A replacement battery is inexpensive and fairly easy to find. If your key fob doesn't respond to your commands, there could be a different issue. It's best to visit a dealer for a spare key. They will make sure that the key is an original Subaru Legacy Key key, which is covered under warranty, and that it is programmed to your vehicle. This is much simpler and safer than buying an aftermarket one from a retailer online.

You can also ask the dealer cut a new key if you provide them with your VIN number and evidence of ownership. They'll utilize this information to encode the replacement key so that it can be recognized by your immobilizer. This is a much more complicated procedure than cutting a single key, and the dealer will charge you more.

Once the new key is programmed then you'll be able switch it to your current key. It takes just five seconds to insert the new key, so keep your working keys close at fingertips. You can take the key off when the security light has stopped flashing and test it.

Battery Replacement

Subaru fobs are extremely useful because they can switch on the sunroof and power windows of your vehicle with just one button press. However, the battery inside your Subaru key fob was not made to last forever and will eventually require replaced. This quick guide from Capitol Subaru will help you to replace the battery on your own.

To start, you'll need to locate the small crevice within the seam that divides the front and back of your key fob. With a small flathead screwdriver you can pop the seam open and reveal a small area inside which is the battery. Remove the old battery, and then replace it with a fresh one, making sure that it is facing the right side upwards. After everything is in place then you can use the new key fob to lock or unlock your vehicle without difficulty!

It's always a good idea to have an additional set of keys at hand especially if you've lost one or not functioning properly. A new key can be purchased at your local auto dealership or you can have one cut from the locksmith. It's important that your key fob is working properly as soon you can so that you can safely drive.