Peugeot 208 Key Replacement

It is recommended to leave the replacement car keys peugeot of Peugeot 208 keys to auto locksmiths equipped with the right equipment and knowledge. They can create and program keys quicker and more efficiently than dealerships.

A dead battery for your coin is most likely to be at fault if your key fob stops locking or unlocking doors. There are other reasons for the key to be malfunctioning.

Dead Coin Battery

A dead battery can stop your Peugeot 208 from locking and unlocking, as well as preventing it from starting the engine. In this situation, you will need to make use of the alternative method for starting as described in your vehicle's owner's manual.

The spark plugs may also be worn out. Spark plugs are what ignite the fuel to start the engine. However, they have a limited time of life. They'll eventually fail in the event that they aren't utilized enough.

Luckily, there is an easy solution to this issue. Check the voltage of your battery using a multimeter. If it is below 11.5 volts, then you need to replace it. It is also necessary to clean the contacts of the battery if it has corrosion. You can do this by lifting the rubber covers that cover both battery terminals and using wire brushes to clean any corroded components of the battery. After that, you need to connect the positive and negative pole cables.

Water Damage

If your 208 won't start and the battery has not gone flat, you should examine the spark plugs. It could be that they are overly dirty, causing them not to spark. The spark plugs can be cleaned in a workshop.

Peugeot cars are equipped with transponder keys that is compatible with the car's immobiliser system. This ensures that only a valid key is able to turn the engine. If the chip inside the Peugeot key is damaged, it won't send the proper signal to the vehicle.

Water damage is a common cause of this problem. This is a frequent issue in colder climates where the vehicle is exposed to rain or snow. In this instance, you should contact a reputable locksmith who will have the required tools and equipment to change the key's programming. They will also have the latest technological know-how and machinery required to make the Peugeot 208 smart key. The process shouldn't take more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot replaced the transponder chips with a new version that makes use of electronic components mounted on a circuit board. The new system is effective when it's brand new but over time the circuit boards start to deteriorate and stop working properly.

This could stop the immobiliser chip activating, so your car won't start. If this is the case, it's a good idea call a Peugeot specialist or locksmith.

Another common issue is when the battery for the key fob begins to fail, which causes the blade of the key to stop being able to feed into the lock. A locksmith from your car will replace the battery, and then cut a new key blade for you. This is a simple solution.

Faulty Receiver Module

If your Peugeot key fob isn't working after dropping it on the floor, getting exposed to a sudden rain or accidently washing it, it could be due a malfunctioning receiver module. The receiver module is responsible for transmitting radio frequencies to the onboard computer that manages the central locking system of your Peugeot vehicle.

Rubber seals on the key fob block water from getting to the electronic chip. However prolonged exposure to water may cause damage to these seals and the chip. The high salt content in the ocean water or pool can cause damage to the key fob if it is submerged.

The module must be replaced if the Peugeot spare key no longer works. This is only done by a Peugeot specialist or an expert auto locksmith. As opposed to other cars, peugeot car key, view site…, keys are protected by a unique immobilizer system that requires the correct coding to start the engine. It is for this reason that you should only trust the Peugeot locksmith to design and program a replacement.

Computer with a problem on board

The on-board computer of your Peugeot is responsible for many of the systems in your car, including airbags and power windows. When something goes wrong with these systems, it will typically display a code that indicates the problem. This code is stored inside the system and remains there until the issue has been resolved. This may require the on-board computers to be replaced.

One of the most frequent causes of the airbag light coming on is loose or corroded connections within the airbag sensor. It can be due to wear and tear, aging or exposure to salt and moisture. This issue needs to be dealt with as soon as you can, because an airbag that is malfunctioning could be dangerous in case of an accident.

If you encounter an error message that says "card not found" on your Peugeot key fob, the battery in the key fob could be dead or weak. This prevents the key fob from sending a signal that disarms the immobilizer on your vehicle's standard. Try this by pressing the unlock key on the key fob, and then trying to start your car. If this fails then the battery on the key must be replaced.