How to Replace a Kia Sportage Replacement Key

For many Kia models keys, there is a keyless entry system built-in. The key functions like an remote control, and can be exchanged with a Kia dealer.

Key fobs are prone to malfunction for several reasons, including the battery of the coin is dead, worn buttons water damage, signal interference, and a defective receiver module. Here are some guidelines on how to get your Kia Sportage replacement key to function again.

How do you replace the remote key or the smart key?

The battery in your kia key replacement's intelligent key will eventually require to be replaced, regardless of whether it's a remote or a push-to-start one, or a regular metal key that doesn't contain transponder. This is particularly in the event that your vehicle displays a message that indicates that the smart or remote key has low battery power.

It's a fairly simple procedure. To replace the battery of the key fob, remove the mechanical key from the slit in the back of the key fob and remove the cover. A small screw will be found inside the key fob to hold the battery in place. Take out the old battery by removing the screw with the help of a small screwdriver. Then, you can insert the new battery and close the slit on the key fob.

Once the key fob has new batteries, test it by pressing the locks and unlock buttons. It's good if the doors lock and unlock as expected. You can now utilize the hands-free feature to lock and unlock your kia key replacement whenever your fingers feel cold or you have to go on errands around Brandon.

Note: Some key fobs (transponder chip or smart keys) might require their programming done. This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) don't require programming. If you're looking to reprogramme your key, you'll need to note the key code number on the tag for the key code.

How do you replace a battery?

If the Kia key fob does not respond when you press the lock/unlock button, it is likely that the battery is depleted. A low battery could cause other problems like the check engine light turning on or the engine not cranking. Fortunately replacing the key fob battery is a relatively easy DIY task that requires only the most basic tools.

Be sure to turn off your vehicle and shut all doors before you begin. Locate the small plastic piece that is on the bottom of your key fob and gently jiggle it until the metal key slips out. The key can be put into the door's driver handle to unlock your car.

To replace the battery on the key fob, remove the rear cover. Use a pry tool to remove the latch that holds the black negative cable. Remove the old battery, and then align the new battery to ensure that the "+" positive side faces you, and the "negative" negative side is facing towards the fob's electronic contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid damaging or breaking the contacts made of metal.

Once the new battery has been installed, turn the key fob off and on in the ignition until the door locks. Then, test your Kia key fob to see whether it's functioning properly again.

How can you replace the smart key

You can have an ordinary keyfob or Smart Key depending on the model of Kia Sportage. The difference between them is that the smart key comes with a small mechanical key blade in it, whereas the standard fob isn't equipped with. Both key fobs are equipped with batteries that will eventually need to be changed. Fortunately, it's quite simple and only takes about two minutes.

Be sure to switch off your Kia, and be on a flat and well-lit surface prior to you begin. Be aware that there are tiny pieces inside the fob which could be snagged if not cautious.

The first step is to locate the small release button that is located on the lower backside of your fob. It will be an oval or circular slot. Once you press this the mechanical key blade will be released and you will be able to open the key fob.

Once you have the key fob opened then you can take out the old battery and replace it. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. After you've finished, you should be able to lock or unlock your car with your key fob - even if the engine isn't running!

How do you replace the mechanical key?

The Kia key fob is a great feature that lets us lock and unlock our vehicle with the click of a button. However, like all devices it will encounter issues occasionally. Luckily, there are methods to troubleshoot these issues and ensure that our key fobs are in good condition for the long run.

A dead or low-quality battery is one of the most common problems. This can cause the device to cease working or to work intermittently. If this is the problem then replace the battery with an entirely new battery.

If this doesn't solve the problem Try using a standard flathead screwdriver to wedge open the fob's plastic casing. Be careful not damage any internal components or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a brand new one.

After the new battery has been put in, close and then open the doors using the mechanical key (every kia fob has an emergency mechanical key that can fit in the slot). Test the key fob to make sure it is working correctly. If the fob still isn't working, call an expert locksmith or dealer to solve the issue. To avoid locking outs in the future, make sure you get an emergency key that will be able to work with all trunk and door cylinders.