How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models has the keyless entry feature built into. The key can be compared to the remote control and can be replaced by a new one purchased from an Kia dealer or a locksmith.

Key fobs may stop working due to various reasons, such as a dead coin battery, worn buttons or buttons, signal interference, water damage and a faulty receiver module. Here are some suggestions to assist you in getting your Kia key fob that is a replacement for the sportage for good.

How do you replace a remote key or smartkey

The battery in your Kia's intelligent key will eventually need to be replaced, whether it is a remote key as well as a push-to start key or a regular key that is not equipped with transponder. This is particularly in the event that your car displays a message that the smart key or remote has a low battery.

Luckily, it's an easy process. To replace the battery on the key fob, remove the mechanical key from the hole in the back of the key fob. Then break the cover. Inside the key fob there will be a small screw that holds the battery in the correct position. Remove the old battery by detaching the screw with a small screwdriver. Then, insert the new one and close the slit inside the key fob.

Test the key fob by pressing the lock or unlock buttons. If the doors unlock and lock as expected, then you're in good shape! You can now take advantage of the hands-free lock/unlock feature on your Kia when your fingers are cold or you have to run some errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may require their programming completed. This requires a machine for programming which is available to the automotive locksmith or dealer. Other keys (non-transponder metal keys) don't require programming. If your key needs to be programmed, you must be aware of the number that is stamped on the tag that identifies the key and keep it in a safe place.

How do I replace a battery

If the Kia key fob does not respond to pressing the lock or unlock button, it's a sign that the battery is not fully charged. A weak battery can cause other issues such as the check engine light flashing on or a delay in cranking the engine. Fortunately replacing the key fob battery is a simple DIY project that requires just the most basic tools.

Make sure that you shut off your vehicle and shut all doors prior to starting. Locate the small plastic piece on the bottom of your key fob and play with it until a metallic key slips out. You can then insert the key in the door handle of the driver to open your car.

To replace the key fob's battery, remove the rear cover and use a plastic bar tool to release the latch that holds the black negative battery cable. Remove the old battery and then align the replacement battery in a way that its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position, avoiding excessive force to avoid damaging or bending the contacts on the metal.

After you have installed the new battery after which you turn the key fob on and off in the ignition until the door locks up. Then, you can test your kia picanto car key replacement key fob to determine whether it's working again.

How do you replace the smart key?

Depending on the model of the kia sportage key fob replacement [linked resource site] Sportage, you may have a standard key fob or a smart key. The difference between them is that the smart fob has the small blade of a key hidden within it, whereas the standard fob isn't equipped with. Both types of key fobs are equipped with an internal battery which eventually needs to be replaced. This is a straightforward process that takes less than two minutes.

Before you begin it is important to make sure that you are on a level surface with enough lighting and that your Kia is turned off. Be aware that the fob can contain small pieces that could fall when you're not careful.

The first step is to locate the small release button on the lower backside of the fob. It could be a circular silver button or a rectangular slot. After pressing this button mechanical key blade, it will come out and you will be able to open the key fob.

Once the key fob is opened, remove the battery. The new battery is CR-2032, and can be bought from a local or online auto parts shop. When you're done, the key fob should allow you to lock the vehicle, unlock it, and then start your vehicle even if it's not running.

How do you replace a mechanical key

The Kia key fob is a fantastic option that lets us lock and unlock our car at the click of a button. But like any device, it can have problems occasionally. There are solutions to solve these issues and keep your key fobs working for a long time.

One of the most frequent problems is a weak or dead battery. This can cause your device to stop working or work intermittently. If this happens, try replacing the battery with a fresh new one.

If this doesn't solve the problem you can try using a standard flathead screwdriver and wedge it into the fob's plastic casing. Be careful not to damage any internal components or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a brand new one.

Close and open the door using the mechanical key. (Every Kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob and verify that it's working correctly. If the key fob isn't working, contact a dealer or locksmith to help resolve the problem. To avoid future lockouts, ensure you have an emergency key that can work on all door and trunk cylinders.