How to Replace a Kia Sportage Replacement Key

The key of a lot of kia sportage key replacement models comes with a keyless entry system built in. The key can be compared to an electronic remote and is able to be replaced by a new one purchased from an Kia dealer or locksmith.

Key fobs might stop working for a variety of reasons, such as an empty coin battery, worn buttons signals, signal interference, water damage and a malfunctioning receiver module. Here are some helpful tips to help you get your Kia sportage replacement kia key (magachem.com) key to work again.

How do you replace the remote key or smartkey

If your Kia is equipped with an intelligent key, remote key, push-to-start key, or a standard non-transponder key made of metal, the battery in these keys will eventually require replacing. This is especially relevant if your car displays a message indicating that the smart or remote key has a low battery.

Fortunately, it's an easy procedure. To replace the battery on the key fob take out the mechanical key from the slit on the back of the key fob. Next, lift the cover. Inside the key fob there will be a small screw that holds the battery in place. Remove the old battery by unscrewing the screw with the help of a small screwdriver. Insert the new battery and then close the cut on the key fob.

When the key fob is equipped with new batteries, test it by pressing the lock and unlock buttons. You're in good shape when the doors lock or unlock as you expect. You can now utilize the hands-free feature to lock and unlock your kia replacement key when your fingers get chilly or when you need to go on errands around Brandon.

Note: Certain key fobs may need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or automotive locksmith can access. Other keys (non transponder metal keys) do not require programming. If you're looking to reprogramme your key, you'll have to record the key code number on the key code tag.

How do I replace the battery?

If the Kia key fob is unable to respond to pressing the lock/unlock button, it is likely that the battery is insufficient. A weak battery can cause other issues, such as the check engine light coming on or delayed cranking of the engine. Fortunately, replacing the battery on the key fob is a relatively easy DIY project that requires just some basic tools.

Make sure that you shut off your vehicle and close the doors before you begin. Locate the small metal or plastic piece on the bottom of your key fob and gently jiggle it until the metal key slips out. You can then insert the key into the door handle of the driver to unlock your car.

To replace the key fob battery, take off the cover on the rear and use a plastic pry bar tool to loosen the latch holding the black negative battery cable. Remove the old battery and then orient the replacement battery so that its "+" side is facing you and the "-", negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid damaging or bending the metal contacts.

Once the new battery is installed then turn the key fob off and back on in the ignition until the door locks cycle. Then you can test your Kia key fob to determine whether it's functioning properly again.

How can you replace the smart key

Depending on the model of your Kia Sportage, you may have the standard key fob, or a smart key. The difference between the two is that the smart key is equipped with the small blade of a key hidden within it, whereas the standard fob does not. Both kinds of key fobs come with an internal battery that eventually will need to be replaced. Luckily, this is a fairly simple process that only takes about two minutes.

Before you start before you begin, ensure that you're on a flat surface with good lighting and that your Kia is off. Keep in mind that the fob has small pieces that could be thrown off should you not be careful.

The first step is to find the small release button that is located on the lower backside of your fob. It could be an oval silver button or a rectangular slot. Once you press this button, the mechanical blade will be released and you can then open the key fob.

Once the key fob is open, remove the battery that was in it. The new battery is a one called CR-2032 and can be purchased from a local or online auto parts store. When you are done, you should be able to lock, unlock and start your car with your key fob even if the engine isn't running!

How to replace a mechanical key

The Kia keyfob is an excellent convenience which allows us to lock or unlock our car by simply pressing the button. Like any other device that is used, the Kia key fob can occasionally have problems. There are solutions to fix these problems and keep your key fobs in good working order for a long time.

One of the most frequently encountered problems is a weak or dead battery. The battery could cause the device to stop working or work intermittently. If this is the case then replace the battery with a new one.

If this does not resolve the problem, use a flathead screwdriver standard to wedge the fob's casing made of plastic open. Be careful not to scratch any internal components or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a new one.

Once the new battery is installed, close and unlock the doors using the mechanical key (every key fob in the kia has an emergency mechanical key that can fit in the slot). Test the key fob to ensure it's functioning properly. Contact a dealer or a locksmith to resolve the problem in the event that the fob is not working. To avoid a lockout in the future ensure that you have an emergency key that can work on all trunk and door cylinders.