How to Replace a Kia Sportage Replacement Key

The key of many Kia models has an electronic keyless entry system built in. This key is similar to remote controls, and is exchangeable by a Kia dealer.

Key fobs might stop working due to a number of reasons, including an inactive battery, worn out buttons signals, signal interference or water damage. Here are some suggestions on how to get your Kia Sportage replacement key back to working.

How to replace the remote key or smart key?

Whether your Kia comes with an intelligent key, remote key push-to-start key, or a regular non-transponder steel key, the battery in these keys will eventually require replacement. This is particularly true if the vehicle displays a message that indicates that the smart or remote key is not powered by the battery.

This is a relatively simple process. To replace the key fob battery remove the mechanical key from the slit at the back of the key fob. Next, pry open the cover. A small screw is inside the key fob, which holds the battery in the correct position. Take out the old battery by removing the screw using the help of a small screwdriver. Then, insert the new one and close the hole in the key fob.

Test the key fob by pressing the lock or unlock buttons. If the doors unlock and lock exactly as you expect, then you're all set! You can now use your Kia's hands-free lock/unlock feature whenever your fingers feel cold or you have to run some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming done. This requires a particular programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If your key requires to be reprogrammed, then you will need to be aware of the key code printed on the tag that identifies the key and keep the number in a secure place.

How do I replace a battery

If the kia ceed key fob replacement key fob doesn't respond to pressing the lock or unlock button, it is likely that the battery is low. A low battery may also cause other issues, such as the check engine light turning on or a delay in cranking the engine. Fortunately replacing the battery on the key fob is a relatively easy DIY task that requires only a few tools.

Be sure to turn off your vehicle and shut all doors prior to beginning. Find the small metal or a plastic piece that is located at the bottom of the key fob. Move it until the key comes out. This key can be inserted into the driver door handle to unlock your car.

To replace the key fob battery, take off the cover on the rear and use a plastic pry bar tool to remove the latch holding the black negative battery cable. Remove the old battery, and then align the replacement battery to ensure that its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damage or bending the metal contacts.

Once the new battery has been installed after which you turn the key fob off and on in the ignition repeatedly until the door locks. Then, you can test your Kia key fob to determine whether it's functioning properly again.

How do you replace a smart key

Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key. The smart key has an embedded mechanical key blade, however, the standard key fob does not. Both types of key fobs have a battery inside them that will eventually need to be replaced. This is a straightforward process that takes less than two minutes.

Make sure you turn off your Kia and stand on a flat well-lit and well-lit area before you begin. Also, remember that there are small parts inside the fob that can fall out if you are not cautious.

The small release button is located on the lower backside. It's either a circular or rectangular slot. You can open the key fob by pressing the button.

After the key fob has been open, remove the battery. The new battery is the CR-2032, and it can be bought through the internet or at a local auto parts store. When you are done it should be possible to lock and unlock your car using your key fob, even if your engine isn't running!

How to replace a mechanical key

The kia picanto key fob keyfob is a wonderful convenience that allows us to lock or unlock our car by pressing one button. Like any device like a key fob, the Kia might have issues. There are methods to solve these issues and ensure that our key fobs are in good condition over the long haul.

One of the most common problems is a weak or dead battery. This can cause the fob to stop working completely or work intermittently. If this is what you are experiencing you should replace the battery an entirely new battery.

If this does not solve the issue, you can use a flathead screwdriver standard to wedge the fob's casing made of plastic open. Be careful not damage any internal components, or scratch the plastic. Once open, carefully remove the battery that was removed and replace it with a new one.

Close and open the door with the mechanical key. (Every kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to verify that it's functioning correctly. If the key fob not working, contact a locksmith or dealer to resolve the issue. Make sure they make you an emergency key that can work across all door and trunk cylinders to avoid lockouts in the future.