How to Replace a Kia Sportage Replacement Key

The key in many Kia models has the keyless entry feature built in. The key can be compared to a remote control and can be replaced by a new one purchased from a Kia dealer or a locksmith.

Key fobs might stop working for a variety of reasons, such as a dead coin battery worn buttons, signal interference, water damage and a damaged receiver module. Here are some guidelines on how to get your Kia Sportage replacement key working again.

How to replace the remote key or smartkey

The battery in your Kia's intelligent key will eventually need to be replaced, whether it's a remote, a push-to-start key or a standard metal key that doesn't contain an electronic transponder. This is particularly when your car displays a message telling you that the smart or remote keys aren't powered.

This is a relatively simple process. To replace the key fob battery take out the mechanical key from the slit at the back of the key fob. Next, lift the cover. Inside the key fob there will be the small screw that holds the battery in its place. Utilizing a small screwdriver take the screw off and remove the battery that was in place. Then insert the new one and close the slit inside the key fob.

Once the key fob has an updated battery Test it by pressing the lock and unlock buttons. If the doors lock and unlock according to your expectations, then you're all set! You can now take advantage of your Kia's hands-free lock/unlock feature when your fingers are cold or you have to run some errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) might require their programming done. This requires a programming machine which is available to the locksmith in the automotive or dealer. Other keys (non transponder keys made of steel) do not require programming. If your key needs to be reprogrammed, you must be aware of the key code number that is stamped on the tag that identifies the key and then record the number in a secure place.

How do you replace a dead battery?

If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a signal that the battery needs to be replaced. A low battery can also cause other issues, such as the check engine light flashing or the engine not running properly. It is easy to replace key fob batteries using just two tools.

Make sure you turn off your vehicle and close all doors prior to beginning. Find the small metal or a plastic piece at the bottom of the key fob. Move it until the metal key comes out. This key can be placed inside the driver door handle to unlock your car.

To replace the key fob battery, remove the cover from the back and use a plastic bar tool to release the latch holding the black negative battery cable. Remove the old battery, and then place the new battery in a way that its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damage or bending the metal contacts.

After you have installed the new battery then turn the key fob on and off in the ignition until the door locks cycle. Then, test your Kia key fob and see if it is working properly again.

How can you replace the smart key

You could have a standard keyfob, or a Smart Key depending on the model of Kia Sportage. The smart key features an embedded mechanical key blade, while the standard key fob does not. Both kinds of key fobs come with a battery inside them that will eventually have to be replaced. This is a simple procedure which takes just two minutes.

Be sure to turn off your kia picanto key fob and sit on a flat well-lit and well-lit area before you begin. Remember that the fob is made up of small parts that can be thrown off if you're not careful.

The first step is to locate the small release button that is located on the back of the lower part of the fob. This will either be an oval silver button or a rectangular slot. When you press it the mechanical key blade will come out and you can then open the key fob.

Once the key fob is removed, you can remove the battery that was in it. The new battery is a CR-2032 that can be bought online or from your local auto parts store. Once you're done you should be able to lock or unlock your car with your key fob even if the engine isn't running!

How do you replace the mechanical key?

The Kia keyfob can be a fantastic convenience which allows us to lock or unlock our car by simply pressing the button. Like any other device, it can have problems occasionally. There are methods to troubleshoot these issues and ensure that our key fobs are in good working condition over the long haul.

A dead or drained battery is among the most frequent problems. The fob could be able to stop working altogether or to work intermittently. If this is the problem then replace the battery with a new one.

If this doesn't fix the problem Try using a standard flathead screwdriver and wedge it into the casing of the fob's plastic. Be careful not to damage any internal components or scratch the plastic. Once the battery is removed and replaced with a brand new battery.

Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to verify that it's working as intended. Contact a dealer, or a locksmith to solve the issue when the fob still is not working. Make sure they make you an emergency key that works for all trunk and door cylinders in order to prevent lockouts in the future.