Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai's bigger dimensions give it a distinct SUV feel. Its ride on 19-inch alloy wheels in Ti and STL versions can also be a bit firm. The front tyres of the Qashqai can lose grip on rough surfaces and its CVT can occasionally display wrist-flexing torque steer.

This is typically caused by an unresponsive coin battery that can be replaced in minutes. Be sure that the replacement battery is the same size, voltage and specifications.

Water Damage

Water damage is one of the most common causes for a Nissan keyfob to display the "key ID incorrect" message. The key fob is fitted with rubber seals that protect the chip inside, but prolonged exposure to moisture could cause it to stop working properly. It is common to observe this if your key fob was dropped into the water or in a swimming pool. But it can also occur when it is wet from rain or soapy hands.

If your key fob is exposed to water for a long period of time, it might need to be cleaned using isopropyl ethanol or electronic cleaner. It may also need to be taken to a professional for repair or replacement.

If your key fob need to be replaced the process is easy. First, ensure you have a multipack with the correct battery (CR2032 3V). Unlock the front and rear cases using the flat-head screwdriver. It is necessary to remove the metal retaining clips and push out the old battery, then insert the new one. Reassemble the fob and replace the mechanical key. Check to see if it functions correctly. If it isn't it is necessary to take it to a local nissan key programming dealer or a professional locksmith to replace the chip on the key. Fortunately, the chip is not normally damaged by exposure to water which means that this shouldn't be too expensive.

Dead Coin Battery

Another common reason the reason your Nissan Qashqai key fob might not function is that the battery inside is dead. They last for three to five years, but may fail over time if the fob has been frequentedly dropped. You can replace the battery with a new one, but make sure that it's the same size and voltage as the original. If you are using another battery, it may cause the key to have an invalid key ID which could prevent it from paired with your vehicle.

The most efficient method to change the battery on the Nissan Qashqai Key Fob is to pry it open using an small screwdriver that has a flat head. In the screwdriver, push it into a small notch on the bottom of the fob, and turn it around gently to separate the two parts of the key fob. Then, remove the old CR2025 button cell battery and insert the new one after confirming its position in the fob.

Examine the terminals for dirt or water damage prior to installing the new battery. If not clean the terminals using small amounts of isopropyl alcohol. Make sure that the pole cables are connected correctly. They should be connected to the positive and negative poles of your battery.

Fault Diagnosis

If your Nissan Qashqai's main fob isn't working after being exposed to clean water from the tap or rain it could be a sign that there is a problem with the internal chip. You'll require a new keyfob if you can't solve the issue by replacing the battery. If the key fob didn't work after dropping it, it's likely that the chip inside was damaged. It is usually possible to get the key fob back to work once again if it is removed and clean the chip with paper towel and isopropyl alcohol, then put it back in.

One common error you will see on your dashboard is "Key ID Not Correct." The vehicle is not able to recognize the key fob, and thus won't allow the car to start. The issue could be caused by many things like water damage, undetectable faults in the key fob's circuitry, or RFID interference.

The key fob will not function if the 12 volt batteries are dead or do not provide enough electric current. This can affect your Nissan Qashqai's remote keyless system central locking, as well as the ability to start the engine with the key fob. If you are unable to unlock or lock the door by hand it is recommended to check the batteries in your key fob and make sure they are in good condition. You could also try re-inserting the battery to reset the transmitter.

Reprogramming

If the key fob was not submerged in saltwater it should be able to be restored to its original state by a simple wash of clean water. You can also clean the electronic chip by using isopropyl or electronic cleaner. If none of these work it is possible to replace the key fob.

If your Nissan Intelligent Key is still not working, there could be a problem with the connection between it and the car. To relink it, start by turning the key into the ignition, without turning on the car. Continue to do this until you see the danger lights flash twice. After that, turn the car off and take away the keys.

Open the fob compartment in your vehicle's fob compartment. It's usually found on a door jamb, or the handle of the door for the driver. Find the small button labeled "program" and press it. Once the process is completed, you should hear a chime.

Now that your Intelligent Key is relinked to the car It's time to test it out. Make sure you press all the buttons on the key while standing a distance from the car. If the lights flash and the horn beeps this means that the key has been successfully linked to the Nissan. You can also test it close to the nissan key replacement near me.