How to Replace a Kia Sportage Replacement Key

For many Kia models keys, there is an integrated keyless entry system. The key can be compared to a remote control and can be exchanged with a new one from an Kia dealer or locksmith.

Key fobs may stop working for several reasons, including the battery of the coin is dead worn buttons signals, water damage, signal interference, and a defective receiver module. Here are some suggestions on how to get your Kia Sportage replacement key working again.

How to replace the remote key or the smart key?

If your Kia comes with an intelligent key, remote key, push-to-start key, or a regular non-transponder steel key the battery in these keys will eventually require replacing. This is especially the case if your car displays a message that indicates the remote or smart keys aren't powered.

Luckily, this is quite simple to do. To replace the keyfob battery take out your mechanical key from the slit that is located at the back of the fob. Then, you need to pry the cover off. A small screw is in the key fob to keep the battery in place. With a small screwdriver, take the screw off and pull out the battery that was in place. Insert the new battery and close the opening on the key fob.

Once the key fob has a fresh battery Test it by pressing the locks and unlock buttons. If the doors unlock and lock according to your expectations, then you're in good shape! You can now make use of the Kia's hands-free lock/unlock feature when your fingers start to get cold or you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming completed. This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If your keys need to be reprogrammed, then you must be aware of the number printed on the tag that identifies the key and then record it in a secure location.

How do I replace the battery?

If the Kia key fob is unable to respond when you press the lock/unlock button, it's likely that the battery is insufficient. A low battery can also cause other issues, such as the check engine light coming on or the engine not working properly. Fortunately, replacing the key fob battery is a fairly simple DIY project that requires just a few basic tools.

Before you begin the process ensure that your vehicle is off and that all doors are shut. Find the small, metal or plastic piece that is on the bottom of your key fob, and jiggle it until a metal key is released. This key can be placed inside the driver door handle to unlock your car.

To replace the key fob battery, take off the cover at the rear and use a plastic pry bar tool to loosen the latch holding the black negative battery cable. Take the old battery out, and then place the new battery in a way that its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damaging or breaking the metal contacts.

After installing the new battery and turning the key fob off and on in the ignition until the door locks up. You can then test the kia key fob replacement's Key fob once more to ensure it's functioning properly.

How do you replace the smart key?

Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The smart key is equipped with an embedded mechanical key blade however, the standard key fob does not. Both types of key fobs have an internal battery which eventually needs to be replaced. It's an easy process that only takes about two minutes.

Before you begin it is essential to ensure that you are on a level surface with adequate lighting and that your Kia is off. Keep in mind that there are tiny parts inside the fob that could fall out if not cautious.

The first step is to find the small release button that is located on the lower backside of your fob. It could be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

After the key fob has been open, remove the old battery. The new battery is a CR-2032, and can be purchased through the internet or at a local auto parts shop. When you're done, the key fob should permit you to lock, unlock, and start your vehicle even if it's not running.

How do I replace the mechanical key?

The Kia key fob is a wonderful option that lets us lock and unlock our vehicle with the push of the button. Like any device it is possible that the Kia key fob might have issues. There are ways to resolve these issues and keep your key fobs working for the duration of.

One of the most frequent problems is a dead or dead battery. This could cause your device to stop working or operate intermittently. If this is the issue you should replace the battery an entirely new battery.

If this doesn't solve the issue, you can use a flathead screwdriver standard to push the fob's casing made of plastic open. Be careful not to damage internal components, or scratch the plastic. When the battery is open, carefully take off the old battery and replace it with a brand new one.

When the new battery is in, shut and open the doors with the mechanical key (every key fob in the kia has an emergency mechanical key that will fit into the slot). Test the key fob to ensure it's working properly. Contact a dealer or locksmith to resolve the problem in the event that the key fob is not working. To avoid lockouts in the future, ensure that you have an emergency key that can be able to work with all trunk and door cylinders.