How to Replace a Kia Sportage Replacement Key

For a variety of Kia models keys, there is the keyless entry system that is built into the key. The key functions like the remote control, and is exchangeable by a Kia dealer.

Key fobs can stop working due to various reasons, such as an empty coin battery worn buttons or buttons, signal interference, water damage and a damaged receiver module. Here are some suggestions on how you can get your Kia Sportage replacement key back to working.

How to replace a smartkey or remote key?

Whether your Kia is equipped with an intelligent key, remote key, push to start key or regular metal non-transponder key The battery inside these keys will eventually need replacement. This is especially in the event that your car displays a message telling that the remote or smart key is not powered by the battery.

Luckily, it's an easy procedure. To replace the battery on the key fob, remove the mechanical key from the slit at the back of the key fob. Next, break the cover. Inside the key fob, there will be tiny screws that hold the battery in its place. Remove the old battery by unscrewing the screw with a small screwdriver. Install the new battery and then close the gap on the key fob.

When the key fob is equipped with an updated battery Test it by pressing the locks and unlock buttons. It's okay If the doors lock and unlock as you expect. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers become chilly or when you need to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming done. This requires a programing machine which is available to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of metal) are not required for programming. If you want to change the programming of your key, you'll need record the key code number on the tag for the key code.

How do you replace a dead battery?

If the Kia key fob is unable to respond when you press the lock/unlock button, it is most likely that the battery is depleted. A battery that is not functioning properly could cause other issues such as the check engine light flashing on or delayed engine cranking. Fortunately, replacing the battery on the key fob is a simple DIY project that requires just a few basic tools.

Make sure to shut off your vehicle and close the doors before you begin. Find the small metal or plastic piece on the bottom of your key fob and move it until a metal key pops out. You can then insert this key into the driver's door handle to unlock your car.

To replace the key fob battery, remove the rear cover and use a plastic bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery and align the new one in a way that the "+" positive side faces you, and the "negative" negative side is facing towards the fob's metal electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.

After installing the new battery, turn the key fob off and on in the ignition until the door locks cycle. You can then test your Kia's key fob again to make sure it's functioning properly.

How do you replace the smart key

You can have the standard keyfob or Smart Key, based on the model of Kia Sportage. The difference between these is that the smart key comes with tiny mechanical key blade tucked inside it, while the standard fob doesn't. Both key fobs are equipped with batteries that eventually require replacing. This is a simple procedure which takes just two minutes.

Before you get started it is important to ensure that you are on a flat surface with enough lighting and that your Kia is turned off. Also, keep in mind that there are tiny parts inside the fob which could fall out if not vigilant.

The release button for the small size is located on the lower backside. It will be a circular or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open it is easy to take out the old battery and replace it. The new battery is a CR-2032 that can be purchased online or at a local auto parts store. Once you're done, your key fob should allow you to lock, unlock, and start your vehicle, even if it isn't running.

How do you replace the mechanical key?

The kia picanto car key replacement keyfob is an excellent convenience that allows us to lock or unlock our car by pressing the button. As with all devices like a key fob, the Kia can have issues at times. There are ways to solve these issues and keep your key fobs working for an extended period of time.

A dead or low-quality battery is one of the most common problems. This can cause the device to stop working completely or even to stop working intermittently. If this is the case then try replacing the battery with a new one.

If this doesn't fix the issue you can try using a standard flathead screwdriver to wedge open the casing of the fob's plastic. Be careful not damage any internal components, or scratch the plastic. Once open, carefully remove the old battery and replace it with a brand new one.

Close and open the door with the mechanical key. (Every kia fob comes with an emergency mechanical key that fits into the slot). Test the fob to make sure it's functioning correctly. If the key fob isn't functioning, contact an expert locksmith or dealer to resolve the issue. Make sure they make you an emergency key that functions in all the trunk and door cylinders in order to avoid lockouts in the future.