Reasons Your Fiat 500 Key Fob Won't Work

A key fob with the fiat keys replacement 500 number is a convenient method to unlock the doors and get started the car. There are many reasons the key fob might stop working. This could be due to a dead coin-battery and water damage, as well as problems with the receiver modules, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote - look-alike Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here to search for a Locksmith Search). This remote includes trunk, lock and unlock buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob will not function is an inactive battery. Modern key fobs have a very restricted operating range, and should be within some feet of the vehicle in order to function. If you're far from your vehicle and hit the keyfob, it won't respond and display the message "Key Fob Not Detected".

If this happens, simply replace the battery on your coin cell (Part number CR2032) by a new one from a reputable brand such as Panasonic, Duracell, or Energizer. They are usually available at your local hardware store or online.

After you've replaced the coin cell battery It is possible to test it by standing near your Fiat Keys Replacement 500 and pressing the buttons. The parking lights should light up and the key fob will operate the lock and unlock switches.

If your key fob isn't working even after replacing the battery, there may be water damage which prevents it from connecting to the module inside your vehicle. Water damage can occur in a variety of ways, from small splashes to submerging the fob salt water at the beach. If you think your fob was exposed to water, you can place it in a bag of rice to draw out the moisture. If this doesn't work, your fob may require reprogramming by a professional auto locksmith or dealer.

Water Damage

Water damage can occur when you immerse the fob into the ocean, or wash it in a washer. Saltwater is especially dangerous to the circuit board of the fob which causes it to short out and eventually end up dying. In the event that you let your fob get wet, it's not an option but if you accidentally drop it in a cup of water or forget to remove it from your pants pocket before running the washer do not give up hope.

First, remove the battery from the fob. Before replacing the battery clean the electronic chip using isopropyl or another similar product. Check the fob again to check if it's functioning. If the key does not function it could need to be reset. This is usually handled by an auto locksmith or dealer.

If the key you have is older and is not programmed for your vehicle You will need to replace it completely. This is a straightforward process that can be completed by a professional locksmith for automotive use. The locksmith must cut the key to match the ignition on your vehicle. They'll also have to reprogram the fob to the car's system. This is a quick and inexpensive process that is usually completed within the next day.

Receiver Module Issues

One of the main reasons why your 500 key fob could stop functioning is that it's out of range. The remote typically has a range of 30 feet or less, and if it's too far away from your car it won't respond to your commands. It can be solved by moving closer to your vehicle until it starts responding.

If you've replaced the battery on your coin (commonly known as a "button" or "watch") and your fob doesn't function it could be due to an internal circuit board problem. In most cases, reprogramming the fob can resolve the issue. You can find directions on how to do this for the majority of vehicles by searching YouTube or checking out the owner's manual.

It is possible to replace the metal clips that hold the coin batteries in the correct position. If they lose tension, they could stop the battery from being seated properly and cause the remote to malfunction.

In rare cases, the fob may become disconnected from your vehicle due to software or hardware issues. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In some cases they may have to reinstall the program in your body control module, too.

Interference

Interference can also cause the key fob to not receive or transmit an signal. This can occur when the key fob is in close proximity to a radio transmitter, like a cell phone or radar detector. The key fob could not function due to a poor connection with the buttons water damage or damage to the internal chips.

If the key fob has been unable to function for a while without notice and you've tried every option at home to fix it e.g. You might have a damaged 500 receiver module in the event that you've tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module is located under the dash and picks up the radio frequency signals from the key fob. It converts the signals into electronic commands that are then translated by the vehicle.

There's a simple method to reset the 500's on-board system, including the keyfob. Disconnect the battery 12 volt for approximately 15 minutes by removing the negative cable and then the positive cable. Then reconnect the battery. This will clear out any residual electricity and restart the car's computer system, which could allow you to get your key fob working again. If the problem persists you should seek out an expert technician. They'll be able diagnose the exact cause of your problems.