Reasons Your fiat 500 keys [simply click the following website page] 500 Key Fob Won't Work

A key fob from fiat 500 spare key 500 allows you to easily open doors and start your car. There are many reasons why the fob won't work. This includes a dead coin-battery, water damage, problems with receiver modules, as well as interference.

This listing is for a NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths for automotive locksmiths). It includes trunk, lock and unlock buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob won't function is due to a dead battery. Modern key fobs only have an operating range that is limited and must be within a few inches of your vehicle to function. If you are further away from your vehicle and hit the keyfob, it will not respond and display the message "Key Fob Not Detected".

If this occurs then replace the battery for your coin-cell (Part Number CR2032) by a fresh one of a reliable brand, such as Panasonic Duracell or Energizer. They are available at your local hardware store or online.

After you've replaced the battery of your coin cell It is possible to test it by standing in front of your Fiat 500 and pressing the buttons. The car will blink its parking lights, and the key fob will operate the lock and unlock buttons.

If your fob's key isn't working even after replacing the battery, it may be water damage that hinders it from communicating with the module in your vehicle. Water damage can happen in a number of ways, ranging from a light splash to submerging the fob into salt water at the beach. If you think your fob was exposed to water, you can place it in a bag of rice to draw out the moisture. If that doesn't work the fob might need to be reset by an experienced auto locksmith or dealer.

Water Damage

Water damage can happen if you immerse the fob in the ocean, or wash it in a washing machine. Saltwater can cause the circuit board to short, and eventually fail. It's not a good idea to submerge the fob in water however, don't give it up if you accidentally drop it in water or forget to take it out of your pants pocket.

Take the battery off first. Before replacing the battery clean the electronic chip using isopropyl, or a similar product. Test the fob next to determine if it's working. If the key doesn't work, it may have to be reprogrammed. This is usually done by an auto locksmith or dealer.

If the key is newer and hasn't been programmed to your car, it will likely need to be replaced completely. This is a simple process that can be carried out by a professional automotive locksmith. The locksmith needs to cut the key to match the ignition of your car. They'll also need to reprogram the fob to your vehicle's system. This is a cost-effective and quick process that could be completed the same day.

Receiver Module Issues

The 500 key fob could not work because it's out of range. The remote has a maximum range of 30 feet. So when you're too far from your car it won't respond to your commands. It is possible to solve this issue by moving the remote closer to your vehicle until it responds.

If your fob does not work after you replace the battery in the coin, also called a "button", "watch" or "button" it could be a problem with the internal circuit board. Reprogramming the fob usually resolves this problem. The instructions are available for most vehicles on YouTube or in the owner's guide.

It is possible to replace the metal clips that hold the coin batteries in the correct position. If they lose tension it could hinder the battery from being seated properly and could cause your remote to malfunction.

In rare instances, the fob may become disconnected from your vehicle due to software or hardware issues. It is possible to fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In some instances the software may require reinstallation in your body control modules.

Interference

In addition to a dead battery on a coin The key fob might not be able to receive or transmit the signal due to interference. This can happen when the key fob is close to radio transmitters (cell phones or radar detectors) or another source of electromagnetic radiation. The key fob could not function because of a problem to the buttons water damage or damage to the internal chips.

If the key fob has been unable to function for a while in the middle of the night and you've tried every option at home to solve it e.g. You might have a damaged 500 receiver module after you've tried replacing the battery, reprogramming or using a spare key fob. The receiver module, which is located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It converts the signals into electronic commands that are then translated by the vehicle.

Fortunately, there's an easy method of resetting all of the onboard systems in your 500 keys, including the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Reconnect the battery. This will clear any residual electricity, and allow you to restart the computer of your car. This can help you get your key fob to function again. If the issue continues you should speak with an experienced technician. They will be able to identify the root of any issues.