Window Handle Repair

The handles on windows can be damaged or missing that makes the window vulnerable to burglars. It's usually not difficult to repair.

Remove the plastic caps at the top and the bottom of the handle. This is an easy task that will take just five minutes with the help of a screwdriver.

Loose Screws

Over time, a window handle may become loose from wear and tear or heavy use. If you feel the handle is wobbly, or it is difficult to open it could be because the screws are loose. This is a simple fix and can be done in a matter of minutes using the help of a screwdriver.

First, remove any plastic caps that cover the screws on the top and bottom of your handle. You can remove them with either a flathead or a fingernail. After the caps are removed then tighten the screw on top until it is secured. Be careful not to tighten it too much because this could cause damage to the screw's head. Then, move to the screw on the bottom and tighten it in a similar manner. After both screws have been tightened, the handle should be sturdier and will open with less difficulty.

If you feel that your window handle is loose, or if the lock paddle cannot be used, it might be time to replace the crank mechanism. You can purchase one via mail order from many replacement hardware experts and it's probably less expensive than replacing the entire handle. You can also tighten the crank by opening the window and then adjusting the crank arm until it is aligned with the notch on the guide track. Then, gently push in on the handle and take off any screws that mount to the trim and remove the casement cover from the window jamb (Photo 1). You'll require new trim screws in the event that any are bent or rusted. Compare the new one with the old one to ensure they are the same, then install it in the manner shown in Photo 5.

It is possible to fill loose wood screw holes with auto body filler before re-tightening them. Select a filler slightly larger than the screw hole to ensure that it will be able to penetrate the surrounding wood when you twist it into place.

Broken Spindle

After a while, the spindle of your window handle could wear out. This can cause the handle to malfunction or not function properly. Fortunately replacing the spindle is an easy and simple fix that can be done by anyone who has basic tools. It is also important to verify the alignment of the handle to make sure that it is securely in the right place.

It's also recommended to apply an oil based on silicone on the handle and spindle after cleaning. This will enable it to rotate more smoothly, eliminating any debris or dirt that might be obstructing its purpose.

Another issue that is common to uPVC casement windows is when the locking mechanism fails. This occurs when the handle doesn't push the spindle across the wedge block correctly. This can be a significant problem as it could prevent your window from closing or opening. You'll need to replace the handle or lock.

It is essential to determine the length of the spindle prior to buying a replacement. This will help you to find the perfect replacement and provides an accurate replacement for the handle you have previously purchased. The measurements are usually on the bottom of the handles however if you are unable to find them, you can contact us to identify the model by phone.

You can also purchase an entire replacement set of handles that have spindles in order to save time and money. These are usually cheaper and can be put in a shorter amount of time.

It's the right time to call a professional if your uPVC tilt-and-turn window remains closed even though you've tried every one of these solutions. A knowledgeable uPVC expert will examine your handle for any issues and provide you with an estimate for repair.

Our range of replacement uPVC handle styles includes keys, inline, espags and cockspurs, as well as cranks. We have a huge selection of both uPVC and aluminum handle models in a variety of finishes. We can also order specific styles for you in the event that we don't have them in stock.

Broken Handle

A broken handle can cause the uPVC handle to shut at any time. It's usually because the handle has cracked internally, preventing it from grasping the spindle. It is unable to operate the window. This problem is common with uPVC handles. It is easily fixed by removing the handle and replacing it.

This can be accomplished by yourself at home with the help of a screwdriver. To remove the handle, use a screwdriver to lift the plastic cap. The screws at the top and bottom should be visible on the base of the handle. With the screwdriver tighten the screw on the top until it is secured. Do not tighten too much as this could damage the handle and the frame of the glass.

After you've made sure that the handle is securely attached to its base, then replace the second screw, which again should be tightened until it is firm. Replace the caps made of plastic on both screws, and your aluminum handle will be functioning exactly as it was intended to.

A worn-out gear in the cranking mechanism can also cause the uPVC handle to not open. The handle could turn, but not move the window, which could cause lots of frustration and is also dangerous for your safety. In this case it is essential to replace the mechanism that operates the handle.

This is a fairly simple procedure and shouldn't take less than a few minutes to complete. However, if you are not confident in this task or would prefer hiring professionals, our team at Bridgewater Glass are happy to assist. We have a lot of experience in replacing and repairing handles made of uPVC and can ensure your double glazed windows are working and safe. Contact us today to learn more about our services.

Broken Base

Over time, a window handle can loosen. It could cause the window to slide or tilt when opened. This usually indicates that the mechanism isn't being secured to the frame by a screw. This is an easy fix, just loosen the screw using a hand screwdriver and then tighten it. Close the window and then slide the handle back to the right position.

Sometimes, the handle may completely disconnect from the base. This can happen in both turn and tilt and standard handles. It is extremely uncommon and is usually only seen in areas with high traffic. This is a straightforward fix that can be accomplished by replacing the old one.

Another problem that is frequently encountered is stripping of the handle teeth. This is usually the cases of older windows that have an oversized crank handle. The teeth are typically made of cast iron and are stripped by excessive use or aging. This is a simple fix that can be done with small vice grips or uPVC casement windows a pair of pliers.

If your handle breaks off from the base section, you will need to remove the crank mechanism to get access and replace the handle. This is a bit difficult for the novice DIYer but with a bit of effort, you'll be able to do it.

Take off the screw that attaches the crank operator to the window frame. Next, open the window until the crank arm guide bushing aligns with the notch in the track. Then using pliers, using a pair of pliers, open the window and slide the guide bushing off the crank arm.

After you have removed the old handle and inspecting the crank stud to see if the teeth are worn. Then, look over the handle for signs that indicate it is worn. Family Handyman advises that if the splines have worn and the handle is damaged, replace it. window crank handle.

To attach the new window crank handle, attach the trim cover to the frame and reattach any screws that have rusted. Make sure the holes for mounting screws are aligned with the holes for mounting on the new handle and then attach the base plate using the remaining screws. Do not overtighten the screw, uPVC casement windows as this could cause the swivel's swivel shaft to break off the track, and also the nylon roller.