Peugeot 208 Key replacement key for peugeot partner van (click here for more info)

It is best to delegate the replacement car keys peugeot of Peugeot keys 208 to auto locksmiths who have the right equipment and know-how. They can create and program new keys much quicker than a dealership and at a lower cost.

If the key fob has stopped locking or unlocking your doors it is likely due to a dead battery in the coin. There are many other reasons for the key to be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as preventing it from starting the engine. In this scenario, you will need to choose the alternate method to start as described in your vehicle's owner's manual.

The spark plugs may also be worn out. Spark plugs are what ignite the fuel to start the engine. They have a limited life span. If they aren't utilized enough to last, they'll eventually fail.

There is a simple solution to this problem. Check the voltage of the battery with a multimeter. If it's below 11.5 Volts, then you need to replace it. It is also necessary to clean the battery's contacts in the event that it is damaged by corrosion. This can be done by removing the rubber covers from the two terminals on the battery and then using a wirebrush, you can remove any parts of the battery that are corroded. Then, you should connect your cables to connect the positive and negative poles.

Water Damage

If your 208 does not start and the battery has not failed, you should look at the spark plugs. You may find that they're dirty and do not spark. The spark plugs can be cleaned in an workshop.

Peugeot cars use transponder keys that works with the car's ignition system. This ensures that only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged then it will not transmit the proper signal to the vehicle.

Water damage is a common reason for this issue. This is most common in colder climates, as the vehicle might have been exposed to snow or rain. In this instance, you should contact a reputable locksmith who will have the required tools and equipment to change the key's programming. They will also have the most up-to-date technological know-how and the equipment required to create a Peugeot 208 smart key. The process shouldn't be more than 15 minutes.

Faulty battery contacts

Peugeot replaced the old transponder chips using a new type that uses electronic components mounted on a circuit board. This new system works great when it's brand new however, over time, the circuit boards begin to deteriorate and stop working correctly.

This could prevent the immobiliser from triggering so that your vehicle will not start. If this happens, it's a good idea call a Peugeot specialist or locksmith.

Another issue that is common is when the battery of the key fob starts to die, this causes the blade of the key to stop from entering the lock. A car locksmith can replace the battery and cut a fresh blade for you, this is usually a simple fix.

Faulty Receiver Module

If your Peugeot key fob was not working after dropping it on the floor, being exposed to a sudden rain or accidentally washing it, it could be due to a malfunctioning receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer which regulates the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals that block water from getting to the electronic chip inside. However, prolonged exposure to water may break through these seals, causing damage to the chip. Submerging the key fob in ocean water on the beach or throwing it into the water can be especially damaging because of the high salt content.

If your Peugeot spare key fob stops working, you'll need to have the module replaced. This can only be done by a skilled auto locksmith or Peugeot specialist. Peugeot keys are, unlike other vehicles, are secured by an immobilizer system. This requires the proper programming to allow the car to start. This is the reason that you should only trust an authorized Peugeot locksmith to create and program an alternative.

Computers with faulty on-board computers

The computer on board in your Peugeot is responsible for a variety of the systems in your vehicle, from airbags to power windows. If something is wrong with these systems, it'll typically display a code that identifies the problem. This code is stored inside the system and will remain there until the issue is fixed. Most often, this involves the on-board computer being replaced.

The most common reason for the airbag warning light to turn on is corrosion or loose connections in the sensor. This could be due to wear and tear, age or exposure to moisture and salt. It is important to have this issue addressed as quickly as possible, as a malfunctioning airbag can be dangerous in the event of an accident.

If your Peugeot is showing a card that is not being detected error then the key battery in the key fob may be weak or dead. This will prevent the key fob from sending a signal that disarms the immobilizer on your vehicle's standard. Try this by pressing the unlock key on the key fob and then trying to start your vehicle. If this doesn't work the battery on the key needs to be replaced.