How to Replace a Saab 9-3 Key

The Saab 9-3 is a great car that has a lot of appeal for drivers. It has a powerful engine as well as good visibility. It also has a top safety rating.

It is vital to have two keys that are compatible for your vehicle. It can be expensive to replace a key if you lose it.

How to replace the ignition Key on the Saab 9-3

You need to change your car key in the event that it isn't turning. This guide will walk you through how to do it on the Saab 9-3. You will need to replace the key, purchase an additional reprogrammable cell and buy a new case for your key-fob.

The majority of modern Saab models utilize transponders instead of a metal key to unlock the car and begin it. The reprogrammable batteries in the key-fob eventually become worn out and will not be able to hold charge. This is particularly applicable if you are using the same key for the lock you have.

The good part is that the battery can be replaced quite easily by an experienced locksmith. You can also do it yourself if have the proper tools and [Redirect-Java] a bit of patience. The first step is to take the key-fob from its case. This is done by inserting a flathead screwdriver into the slot in the middle of the case. The plastic is thin, and can easily be damaged.

Once the case is opened, you can create the new key by combining the lower part of old key with a transponder and banana. This will ensure that the new key is mated to the CIM properly, which could make a huge difference when replacing the original key for your Saab 9-3.

How to Replace the Ignition Key on a Saab 900

Unless you have two keys, you will have to take off the dashboard and steering wheel to gain access to the ignition. Begin by disconnecting the negative battery cable. Once the battery is disconnected, it is possible to remove the dashboard and trim pieces that surround the steering wheel. Once the dash has been removed, you can place screws into the hole behind the ignition switch.

The ignition cylinder comes with a key lock which could prevent the vehicle from starting if you don't have the key inside it. If the ignition switch on your 900 isn't working properly, check the key to see if it's in the lock or snared into the barrel of the ignition. You should also rotate your keys and keep them clean to avoid bent.

Saab cars differ from other cars due to the fact that they don't use traditional metal keys. Instead, the car recognizes electrical signals that come from the key fob via a special microchip in it.

If you lose only one functioning key fob, your dealer will charge you an extra fee to replace your computer module (also known as the CIM). We can however reprogram your existing computer's EEPROM and set it to accept new keys without replacing it. This will save you over 50% of the price the dealer charges! This is the SAAB KEY PROGRAM. Find out more about it here!

how to open a saab 93 without a key to replace the ignition Key in the Saab9-5

The metal component of a classic lost saab keys key is easy to copy, and not much of an impediment against theft of a vehicle. The real security comes from the electronic part inside the key-fob. It has a chip inside that recognizes your car when it is inserted into the ignition switch.

Saab's anti-theft system has relied upon this technology for over a decade. It's not as effective as a door lock, but it makes stealing your car much more difficult. Every Saab owner must keep an extra Saab key in their car.

Most new Saabs come with two keys at the factory. However, you can upgrade them at an authorized dealer using a handheld computer called Tech-2. Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception to this rule is the NG 9-3 vehicles which have more modern, newer features that require keys-fobs.

If you lose all keys, the dealer will replace your CIM or TWICE modules and charge an additional fee for it. But we can reprogram the EEPROM in your existing computer to accept new keys, without replacing the expensive modules.

How to replace the ignition Key in a Saab XC90

If your Saab 9-3 key fob replacement 9-3 key fob is having problems turning the lock barrel it's possible that it's time to replace it. The process is fairly simple and you don't even need to visit a dealership. You can do it at home, using a couple of basic tools.

You'll first need to prepare the new keys. Before you begin, disable the anti-theft feature by placing blocks underneath your rear wheels and engaging your handbrake. Insert the key into the ignition and then turn the key to the "on" position. This will activate the accessories, but will not start the engine. Repeat this process five times and leave the key in the on position.

Then you'll need to buy a new case for your key fob. These are available at most auto parts stores and are typically inexpensive. Depending on the model, you can even buy them without electronics.

To open the case you need to gently push the flathead screwdriver into the slot in the middle. The case should break easily, and when you've done that, you'll have access to the internal electronics. To get rid of the electronics, use a small screwdriver, and try to pry them out with a gentle force.