Window Handle Repair

Window handles can become loose or even broken, allowing the windows open for burglars. It's usually not difficult to repair.

Begin by taking off the caps made of plastic which cover the screws at the top and bottom of the handle. This is a simple job that should take around five minutes with a screwdriver.

Loose Screws

Over time windows handle handles can become loose due wear and tear or heavy use. If you feel that it is wobbly, or it is difficult to open, it could be that the screws are loose. This is an easy fix that can be completed with a screwdriver within minutes.

Remove any plastic caps that are covering the screws on the top and bottom of the handle. You can remove them with either a flathead or a fingernail. Once the caps are removed, begin with the top screw and tighten it carefully until it is secure. It is not recommended to over tighten the screw because it could damage the head. Then you can move to the screw on the bottom and tighten it in a similar way. After both screws are tightened, the handle will feel more solid and open easier.

If your window handle is extremely loose or the lock paddle is unable to be inserted then it's time to get an upgrade to the crank mechanism. You can purchase one via mail order from several replacement hardware specialists and it will probably be cheaper than replacing the entire handle. You can also try tightening the crank that is already in place by opening the window until the guide bushing is aligned with the notch on the guide track. After carefully pushing in on the handle, remove any trim mounting screws and lift the casement away from the window jamb. (Photo 1) You'll need new trim screws if they are rusted or bent. Install the new one as shown in Photo 5 after comparing it with the previous one to make sure they are in line.

It may be necessary to fill in loose screw holes using an auto body filler prior to tightening them again. Filler should be slightly larger than the screwhole in order to ensure that it will bite into wood surrounding it when it is twisted in place.

Broken Spindle

After a while the spindle of your window handle might become worn out. This can cause the handle to fail or stop opening properly. Anyone with a basic tool can change the spindle quickly and easily. It is essential to examine the alignment of the handle to ensure that it is secure in the right place.

It's also recommended to apply an oil based on silicone on the spindle and handle following cleaning. This will allow it to rotate more easily, removing any debris or dirt that could be hindering the work.

Another issue that is common to uPVC casement windows is when the locking mechanism fails. This happens when the spindle isn't pushed across the wedge block in a proper manner by the handle. This can cause a major problem, since it could hinder the window from opening or closing which means you have to replace the lock or handle.

It is crucial to determine the spindle length before buying an alternative. This will help you to find an appropriate replacement and will provide a precise replacement for the handle you have previously purchased. The measurements are usually on the bottom of the handles however if you are unable to find them, you can contact us to identify the model by calling us.

You can also buy a complete replacement set of handles with a spindle in order to save time and money. They are typically less expensive and can be fitted in less time than replacing just the handle itself.

It's time to speak with an expert if your uPVC tilt-and-turn window remains stuck closed after you have tried every solution. A knowledgeable uPVC expert will inspect your handle for any problems and give you an estimate for repair.

Our selection of replacement upvc doors handles includes espag handles, inline, key locking, cranked and cockspur designs. We stock a large number of uPVC handle models and aluminium handles in a variety finishes. We can also order specific designs that aren't available in stock.

Broken Handle

A damaged handle can cause the uPVC handle to stop opening at any point. This is usually due to the handle being broken internally, preventing it from grasping the spindle. It can't operate the window. This is a common problem with uPVC handles, and can be resolved easily by taking the handle off and replacing it with an entirely new one.

It can be done yourself at home with the help of a screwdriver. To remove the handle, use a screwdriver to lift the cap. The screws at the top and bottom should be visible on the handle base. Utilizing the screwdriver tighten the top screw until it is secured. Be careful not to tighten too much it, as this could harm the handle or frame of the window.

After ensuring that the handle is securely attached to its base, you can then replace the second screw, which should be tightened until it is solid. Afterwards, replace the plastic caps on both screws. Your aluminium window handle should now work as it should do.

Another reason why the uPVC window handle might not open is because of a worn-out gear in the cranking mechanism. The handle may turn, but not move the uPVC window. This can be a hassle and a risk to your safety. In this instance it is crucial to replace the mechanism that operates the handle.

It's a relatively easy process that should take more than a few minutes to complete. Bridgewater Glass is happy to assist you if you're uncomfortable or want to hire professionals. We have a great deal of experience with uPVC handle repair and replacement and can ensure that your windows are working and safe. Contact us today to discuss our services and learn more about how we can assist you.

Broken Base

A window handle may become loose over time. Sometimes, it could cause the window to sag or slide open when it is opened. If this is the case it usually means that one of the screws isn't tightening the mechanism to its frame. It is easy to fix. Just loosen the screw with the hand screwdriver, then tighten it. Close the window, and then slide the handle back into place.

Sometimes, a handle can break completely from the base section. This can happen in both turn and standard handles. It is a rare issue and is only found in areas where it is heavily utilized. This is a straightforward fix that can be done by replacing the old device.

Another issue that is common is stripping of the handle teeth. This is typically the cases of older sash windows that have the crank handle. The teeth, which are typically made of cast iron, may be ruined due to excessive use or age. It is a simple repair and can be done with a small vise grip or uPVC casement windows a pair pliers.

In the event that your handle splits off from the base it is necessary to take off the crank mechanism to get access and replace the handle. This can be a bit difficult for the beginner DIYer, but with a little effort, you can accomplish it.

Remove the screw that secures the crank operator to the window frame. Next, open the window until the crank arm guide bushing aligns with the track's notch. Then, using pliers, move the guide bushing away from the crank arm.

After you have removed the old handle take a look at the studs on the crank to see whether the teeth are worn. Next, inspect the handle for signs that indicate it is worn. If the splines are worn you should continue to replace the window crank handle, or look into replacing the entire handle, advises Family Handyman.

Attach the trim cover and any screws that have rusted to the frame prior to installing the new window crank handle. Assemble the base plate by connecting the remaining screws. Make sure that the holes for the mounting screws match the mounting holes of the new handle. Do not overtighten the screw to the point that it causes the swivel's swivel shaft to break off the track and onto the nylon roller.