Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are easy to maintain and durable, as well as long-lasting. As opposed to aluminium and timber they do not get rusty or decay.

It is important to clean and oil UPVC doors and windows on a regular basis. This will help avoid unnecessary repair my windows and doors costs and improve the efficiency of energy.

1. Broken Glass

If the glass in your window has been damaged, it could cause a large amount of damage to your home, Repair My Windows And Doors which can make it very dangerous and potentially fatal. It is essential to take the time to ensure that you're doing all you can to ensure that your windows are in good condition.

Single-pane windows are fairly simple to replace, and they typically fit into frames of the past easily. However when you have double pane windows that are secured by internal beading it will be more difficult to take out the panes that are in place and replace them with new ones. In this case you'll need to source some plastic spacers that will help the new pane to fit correctly into the frame of the window.

Wearing protective eyewear and thick gloves is a must when you are planning to remove the glass by yourself. It is also an excellent idea to lay down a drop cloth before you start working on the glass so that any fragments of glass fall onto the cloth rather than on the floor where they can be trampled on and cause further damage.

Once the glass is removed and the glass is removed, it's a good idea to seal the gap with some clear packaging tape or duct tape to block water and drafts from getting into the home until a professional comes out and fix the window. This will also provide an obstacle to stop intruders from getting into your home. If the gap between the door and the window is substantial, you may need to consider a security screen that also has windows. This will provide the best of both.

2. Sagging

uPVC windows and doors are a low-cost, durable and energy-efficient alternative to timber windows with sash. In time, they could develop a variety of issues that include sliding. A window that is sagging can cause problems with light, draughts or even security. It's crucial to act when you realize that your uPVC windows are sagging.

To fix a sagging window you can try to reposition the hinges. To do this, you'll need to open the window to access the frame. Then, remove both the top and bottom hinges with a screwdriver and adjust them clockwise or counter-clockwise. Once you've repositioned the hinges, close your window and check for fit. If you're satisfied with the fit, you can tighten the screws to ensure they stay in the right place.

If you are unable to reposition the hinges, you could have to replace the seal. As time passes, rubber seals lose their elasticity and dry out and cause them to lose tightness. If this happens, it's essential to replace the seal as soon as you can to ensure that your uPVC windows are waterproof and secure from draughts.

uPVC handles can also loosen up. Most often, this is caused by screws that have become loose over time. However, it could be due to the fact that the handle mechanism has been worn out. It's relatively simple to repair a loose uPVC handle. You'll first need to close the window and then perform an initial fitting. The corner joints of the sash must align with the casing joint. If it isn't then you can make use of a screwdriver to loosen the handle and reverse the mechanism back into its original position.

3. Water Leaks

If you awake to damp floors and mouldy walls each time it rains, it's important to take action. Water leaks through windows can cause structural damage to your home and also affect your ability to regulate the temperature inside your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

This is a relatively easy fix that can be done by any DIY expert. Depending on the severity of the issue is, the old caulking may have to be removed. When it comes to uPVC repair, it is important to be careful not to over-caulk. This will only make your window more difficult to clean and lower its energy efficiency.

Check that any drainage holes are free of debris in them and ensure that the sill pan has been properly angled to drain away from the window. In more serious cases, you may need to replace the window.

Other indicators of long-term water leakage are decayed sills and the appearance of black spots of mold on the wall near the window. The fungus thrives in humid conditions and can propagate quickly throughout the house.

It is also important to note that if the leakage is coming from between the glass in your double glazed windows, it's more likely to be a problem with the glass seal rather than the frame or sagging. Again this can easily be fixed by a uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges may be to blame when your uPVC window is difficult to open or it opens with an ease. Anyone who is a skilled DIYer can fix these in a matter of minutes.

Most households in the UK will have top-hung or side hung uPVC windows that have hinges and, like all mechanical parts, they will wear out over time. It is an easy process, but it's easier to do when you have a person to help you hold the frame up.

Check that the uPVC hinges are open and closed in the right direction. You can check this by looking for the arrows on each hinge, this indicates which way the window should open.

The issue can be caused by opening the window improperly or by a poor installation at the factory. Sending us photos via our website is often enough to resolve the problem. We are always happy to give advice.

Regularly lubricating the hinges is essential. Applying a light engineering lubricant to the hinges is a good method of doing this. We recommend using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can allow the window operate and close more easily. It can also stop corrosion and reduce the risk of sticking. This must be done at a minimum every year. WD40 or other solvent-based lubricants are not recommended as they can cause damage to your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by different things. The hinges can also become unbalanced due to wear, which can cause an opening where the sash and frame meet. They can be repaired by giving them a thorough clean, however when they're beyond repair, it might be necessary to get them aligned or replaced. The interlock may also become disaligned. This is located on the hinge's side and could require to be cleaned. In certain instances, it may be necessary to replace the hinges.

The second most frequent cause of draughts is the window seals, these can become worn down or damaged over time, and allow air to escape through the gaps. Replacing these with high-quality weatherstripping is a good way to stop draughts. Replace the windows made of Upvc with low-emissivity lenses. This will help control indoor temperatures and lessen the possibility of draughts.

Another method of reducing the amount of draughts is to use a Draught-excluder. These are usually fabric tubes filled with a filler, which can be placed over your window sill. They will help keep cold air out and keep your home warm and cosy!

Your upvc windows can remain a great source of insulation and security in your home with a little regular maintenance and repairs. It is crucial to recognise that all windows have a life span and they may reach the point when it's more efficient to replace them than repair them. So, if you're experiencing issues with your upvc window repairs windows, it is best to seek professional assistance as soon as possible.