How to Repair Double Glazed Windows

There are a few telltale indications that your double glazed windows require repair. Obviously, water infiltration or draughts that enter the frames are an obvious indication of window damage and will need to be repaired in the shortest time possible.

The misting could also mean that your window seals are in need of replacement. Replacing the seals will fix the issue and stop condensation, draughts or leaks.

Broken Panes

Broken glass is among the most frequent issues that double-glazed windows face. Double-pane windows are more difficult to break than single panes, but accidents can happen. It is important to repair the broken glass as soon as you can.

Get rid of any glass fragments that might remain in the frame. Wear gloves and eye protection when you remove the glass as it can be very sharp. Examine the floor for fragments that are not fixed after the shards have been removed. Also, it's a good idea to search for any metal hooks that could be keeping the panes in place and remove them too.

Once the glass is removed, you'll need to remove the old glazing compound (small fasteners that hold the glass to the window frame) and replace double glazing glass them with new ones. This is a time-consuming procedure and requires a few tools to complete the task. This includes latex glazing putty; metal glazing points; pliers; a heat gun and a putty knife.

When removing the old glazing compound and points it is best to start at the top of the sash, and move down. This will stop any wood or paint from the sash from sticking to the tool. Also, if you do end up removing some of the sash's wood make sure you employ a chisel, or a utility knife instead of a chemical stripper because this could cause damage.

After you're done you can sand the wood. When it's smooth, you can apply linseed oil or a clear wood sealer to shield it from water and further damage.

There are a few quick fixes that you can try for a window that is cracked by a double-pane However, these solutions will not repair the crack and should be used only as a temporary solution. Use of silicone caulk will help seal the gap. However it is essential to use a high-quality caulk and the correct application techniques.

Condensation

If you notice moisture or mist between the glass panes of your double glazing it means that your window seal isn't working. This could be a problem because it stops the insulating air or seals gas from being trapped between the two glass panes and therefore it can't perform its job properly and this can lead to temperature changes which can cause condensation to form.

A double glazing specialist can fix this issue easily. To fix the problem, your window contractor will remove the affected window sash and IGU (insulating glass unit) before putting in a new gasket to create a sturdy and airtight seal to stop condensation from happening again. They will also apply drying agents to aid in drying the area out and stop the condensation from occurring again.

The other reason why you might notice a misty appearance between the glass panes of windows with double glazing is because the framework has shifted over time, which breaks the all-important seal. This can be a major issue as it means that your windows will not function correctly and will lose energy efficiency.

It is possible to replace double-glazed window's panes, however, it can be costly and is typically only needed when the window is beyond repair. However, if you've spotted the signs of a problem with your double-glazed windows, and you're still within the warranty period, then it may be possible to have it fixed for free or at least at a reduced cost.

It's worth checking the terms of your warranty before you contact the company to see whether they can solve the issue without having to replace the entire window. Double-glazed windows are usually covered by warranties of between 10 to 20 years, which means you might find they can repair double glazing window the faulty window units rather than replacing them completely. If this is the situation they'll likely send out a specialist to fix your double-glazed windows. They're able to accomplish this in a short time. This is a much cheaper alternative than purchasing and installing brand new double glazed windows, and it's more sustainable for the environment as well!

Broken Locks & Handles

When your window handle is broken or hard to open, it can be a major issue since it prevents you from using your windows. This can also give burglars an opportunity to gain entry into your home. There are several solutions to this problem but the most effective solution is to connect with an uPVC professional. They can fix the issue for you, or offer you a new handle.

There are a few different types of window lock, but the most common one is the Maco or Mila locks which are typically found on uPVC frames. These locks use bayonet style rods to lock and these can easily seize up. If this occurs, the handle's nase is stuck in the popped out position and cannot be returned to the wedged locked position. This can be a frustrating issue, but it can be solved by following a few simple steps.

To fix the issue you'll need to take off the handle. This should be simple enough using the help of a screwdriver. After the handle is removed, you should then be aware of the screws that hold the lock to the frame. After the screws have been removed, you can try to grab the bolts with a wrench or pair of pliers. If this does not work, you can insert the tool into the gap between the frame and the window (the gap could be different at the ends of the windows) and then make an "u" shape using your hands to grasp the bolts.

If you manage to unblock the bolts that shoot, then you can shut your window by moving the handle to the closed position. The gearbox (espag or espagnolette.) is most likely damaged and won't open by the handle. You can refit the gearbox (espag or espagnolette) without the shoot bolts, so that the window can still be opened with the handle.

Broken Hinges

If your uPVC window hinges are no longer operating smoothly, you may need to have them repaired or replaced. Whether this is due to them having been opened with too much force, the hinge dropping and snapping or they had a fault in the first place the issue could cause issues that make it difficult to use your window. Thankfully it is simple and quick, so there's no need to purchase windows that are new and you can have your old windows repaired instead.

First, you'll need to remove the existing hinges. To do this, unscrew the screws that attach the frame to the hinges. After the hinges are removed then you can replace the boards using plywood that has been cut to the right size. Make sure the plywood is more robust than the original board to ensure it can support the weight of the window both open and closed. You'll also want to use wood filler to ensure that the hole that was left by the hinge is completely filled and won't leak or become loose in the future.

Once you've replaced hinges and filled the holes, you'll need paint them. Be sure to employ a top-quality paint to ensure it will last for as long as it can. Once the paint has dried, you can reattach the window. Make sure you tighten any screws that are loose.

Window hinges also require regular maintenance. You can help them last longer by cleaning them regularly on the track of friction and lubricating the hinge mechanism. You can also apply wood preservatives in order to shield them from the elements. This will prevent corrosion and keep them looking great for as long as you can.

A double-glazed window can help you reduce your heating bills, as it's more energy efficient than windows with only one glass. However, just like every other part of your home, your windows will show wear and tear and might require repair or replacement as time passes. Our Preston experts can assist you if you observe any indications that your double glazing door locks-glazed windows aren't functioning properly.