How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners have to follow a series of steps that are unique to add an additional ignition key. It requires dealer support using an electronic handheld computer called Tech-2. Then a new car key and transponder must be purchased and then programmed into the car.

Rotate your keys to prevent one from wearing out quicker than the next. This will keep your keys in top condition.

Replacement Case

The new key fobs for keys are not like the older Saab keys. They're equipped with electronic devices that make it difficult to copy. This has made stealing cars significantly more difficult than it was a few years ago. However, it also has made replacing lost keys a much more expensive endeavor.

Every owner of a 9-3 Saab Spare Key should have at a minimum two functioning keys. It costs a fortune to replace a lost key as it requires replacing the CIM module, as well as reprogramming the locking cylinders. Dealers typically charge between $100 and $200 for this.

There are options to avoid these costs. Certain parts suppliers will utilize the code of the spare key to cut a brand new metal blade for less than the price of the dealer. The key must be exactly the same as the original in order for it to work in your vehicle.

You can also replace the case yourself by following these steps. You will need to have a flathead and patience. With the screwdriver slowly tear the plastic away and then separate the emergency key from the case. Once the case has been opened remove all electronics and place them into the new case. Place the key with the correct badge into the case.

Replacement Battery

The replacement battery for the saab key programming 9-3 is a cheap component that can be replaced quickly and easily. This YouTube video by Cyclone Cyd demonstrates how to replace the remote fob battery with only four steps. This tutorial should work for any modern saab-type key fob, however, the procedure may differ slightly.

This button is usually located just below the Saab logo on the back of the fob. It's usually near the Saab logo on the back of the fob. Next, use an screwdriver with a flat head to insert into the small hole of this button. This will be enough to allow you to open the case of the fob to allow you to replace the battery.

After the new battery CR1632 is in place, you can reassemble the remote key fob, and then program it to your car. The whole process should take more than a half hour at the most. It's a very easy process that does not require any special equipment.

The process is more complicated if you lose your key, but still possible. The dealer has to verify the VIN of the car, and then purchase a replacement key blade and TWICE module with the proper unique code. The dealer will then need to program the key using MDI which is a new software tool.

Replacement Key Fob

The key fob is the part that locks and unlocks your car, it's got an internal battery. The batteries have a lifespan that is a long time, and they eventually die. This is a typical issue that occurs with all vehicles, and the good news is that you can replace the batteries in many key fobs without replacing the whole case. You can purchase replacement fobs from Amazon that come with all the electronics already installed, so you can just pop open the case and replace the batteries in the original case. It is necessary to remove the emergency key before you can replace the batteries. To accomplish this, simply insert a small flathead screwsdriver into the slot in the middle of the. The case will split once you work the screwdriver all around it.

If you're about to replace the keys, make sure you have a spare since this will cut down the total cost by a substantial amount. If you have spare keys, you can ask the dealer cut an additional key and program it to your car, Saab Spare Key which is cheaper than replacing the entire key fob.

It is possible to add another key to your vehicle if you don't already have one, but it requires an extensive amount of research and work. It will cost you a few hundred bucks to add a second car key. The computer of the car also needs to be programmed. Professionals can do this but it's not a cheap option.

Replacement Ignition

The modern SAAB 9-3 is an advanced alarm system built on a keycode. If you lose your sole key, it can be costly to get another one since the car must have a specific computer installed and be programmed to accept a new key. Locksmiths typically aren't able to program this or even dealers can charge several hundreds of dollars just to program the new key!

Dealers will charge you top dollar to replace your car computer (also called the CIM or SAAB twice) if you lose your sole working key. Instead, we can reprogram the EEPROM of your current car computer, preparing it for a new key, saving you over 50% of the price you be charged at a dealership.

If you have owned a 9-3 from SAAB for a long time you are aware that the ignition keys aren't very durable. If your ignition key is not working properly, you should think about replacing it. They can become sticky and the buttons are known to fall off. It's not as difficult as it appears to replace the ignition key. With the right tools, it is able to be done quickly.