Reasons Your fiat punto key fob 500 Key Fob Won't Work

A fiat 500 key fob is a convenient way to open the doors and begin the car. There are a myriad of reasons the key fob might stop working. This could be due to a dead battery water damage, receiver modules issues, and interference.

This listing is for an NEW replacement fiat 500 key fob not working Flip Key Remote - look-alike Ilco brand that must be programmed professionally by a local automotive locksmith (click here for Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob that isn't working. Modern key fobs offer an operating range that is limited and must be within a few inches of the vehicle in order to work. If you are far from your car and press the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a fresh one from a reputable brand like Panasonic Duracell or Energizer. You can typically find them in your local hardware store, or online.

After you've changed the battery on the coin cell You can test it by standing in front of your fiat key replacement near me fiat 500 spare key cost uk and pressing the buttons. The car should flash its parking lights and the key fob should operate the lock and unlock switches.

If the fob's key doesn't function after replacing the battery, it may have water damage that prevents it from communicating with the receiver module inside your vehicle. Water damage can happen in many ways, including a simple splash or submerging the key fob in saltwater at the beach. If you believe your fob was exposed to water, you can place it in a bag of rice to draw out the moisture. If this doesn't work your fob will probably need to be reprogrammed by an experienced locksmith or dealer.

Water Damage

Water damage can happen if you submerge the fob in the ocean or wash it in a washing machine. Saltwater poses a particular risk to the fob's circuit board and can cause it to short out and eventually end up dying. Getting the fob wet is not an ideal choice but if you drop it in a glass of water or fail to take it out of your pants pocket prior to running the washing machine Don't give up hope.

Take the battery off first. Clean the electronic chip using isopropyl alcohol or another similar product and then dry it thoroughly before replacing the battery. Check the fob to see if it is working. If the fiat abarth key isn't working, it may have to be reprogrammed. This is usually done by an auto locksmith or dealer.

If the key is more recent and has not been programmed to your vehicle it is likely to need to be replaced completely. This is a straightforward process that can be completed by a professional locksmith for automotive use. The locksmith will have to cut the key to match the ignition of your vehicle. They'll also have to reprogram the fob for your car's system. This is a low-cost and fast process that can be completed in the same day.

Receiver Module Issues

One of the simplest reasons your 500 key fob might stop functioning is because it's out of range. The remote's range is of 30 feet. Therefore, if you are too far away from your vehicle, it won't respond to your commands. You can fix this by moving the remote closer to your car until it responds.

If your fob doesn't work after you replace the battery inside the coin, which is also called a "button", "watch" or "button", it could be a problem with the internal circuit board. Reprogramming your fob can resolve this issue. You can find the steps for most vehicles on YouTube or in the owner's manual.

It is possible to replace the clips made of metal that hold the coin batteries in place. If they lose tension, it could hinder the coin battery from sitting properly and could result in the malfunction of your remote.

In rare instances, the fob may be out of alignment with your vehicle because of hardware or software issues. This could be a huge headache, but you can often fix this by visiting an auto locksmith to have them reprogram your fob for you. In some cases it may be necessary to reinstall the software in your body control module, as well.

Interference

Interference can also cause the key fob to not be able to receive or transmit signals. This could happen when the keyfob's location is in close proximity to a radio transmitter like a cell phone or radar detector. The key fob might not function because of a problem with the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to resolve it (e.g. replacing batteries, reprogramming or using the spare key fob, it could have a damaged receiver module on your 500. The receiver module is located under the dash, and it picks up the radio frequency signals from the key fob. It converts the signals into electronic commands, which are then translated by the vehicle.

Fortunately, there's an easy method of resetting all of the on-board systems in your 500 and include the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Then reconnect the battery. This will clear any residual electric current, and also restart the computer of your car. This will help you get your key fob to function again. If the issue persists it is recommended that you consult an expert technician. They will be able to identify the root cause of any problems.