Reasons Your fiat remote key Panda Key Fob (Notabug.Org) 500 Key Fob Won't Work

A key fob for fiat spare key 500 allows you to easily open doors and start your vehicle. However, there are numerous reasons why the fob may stop functioning. This includes a dead coin-battery or water damage, issues with the receiver module, and interference.

This listing is for an NEW replacement fiat keys replacement Flip Key Remote - look-alike Ilco brand that needs to be programmed professionally by a local locksmith (click here for Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob won't function is an inactive battery. Modern key fobs come with a restricted operating range, and should be within just a few feet of the vehicle in order to function. If you're far from your car and hit the keyfob, it will not respond, and display the message "Key Fob Not Detected".

If this happens, replace the battery of your coin cell (Part number CR2032) with a new one from a trusted brand like Panasonic, Duracell, or Energizer. You can find them in the local hardware store or online.

You can test the battery of your coin-cell by pressing the buttons while standing near your fiat ducato remote key programming 500. The parking lights should blink and the key fob will operate the lock and unlock switch.

If the fob's key doesn't function after replacing the battery, it could be damaged by water, which prevents it from communicating with the receiver module inside your vehicle. Water damage can happen in a number of ways, ranging from an accidental splash to submerging the fob salt water at the beach. If you suspect that your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture back out. If this doesn't work, your fob will probably need to be reset by a professional locksmith or dealer.

Water Damage

Water damage can occur when you submerge the fob in the ocean, or wash it in a washing machine. Saltwater can cause the circuit board to short and then die. If you get the fob wet, it's not an ideal idea, but if you drop it into a cup of water or do not remember to remove it from your pants pocket before running the washing machine Don't give up hope.

First, remove the battery. Before replacing the battery, clean the electronic chip with isopropyl, or a similar product. Next try the fob and verify if it is working. If the key does not work, it may have to be reprogrammed. This is usually done by a dealer or professional auto locksmith.

If your key is old and is not programmed to work with your vehicle then you'll need to replace it completely. This is an easy process that can be carried out by a professional locksmith for automotive use. The locksmith will need the key cut to match the car's ignition. The locksmith will also have to program your fob into the car's system. It's a simple and affordable process that is usually completed on the same day.

Receiver Module Issues

One of the main reasons your 500 key fob might stop functioning is that it's out of range. The remote usually has an operating range of 30 feet or less, and if it's too far away from your car it won't respond to your commands. You can easily solve this problem by moving the remote closer to your car until it responds.

If your fob doesn't work after you replace the battery for the coin, also known as a "button", "watch" or "button" It may be due to a malfunction on the circuit board inside. Reprogramming the fob typically resolves the issue. You can find the instructions for most vehicles on YouTube or in the owner's manual.

It may be necessary to replace the metal clips that hold the coin batteries in their place. If they loose tension, it can prevent the battery from being properly seated and cause your remote to malfunction.

In rare instances, the fob can become out of sync with your vehicle because of hardware or software problems. This can cause a major issue, but you are able to often fix this by visiting an auto locksmith to have them reprogram your fob for you. In certain instances the software might need to be reinstalled in your body control modules.

Interference

Interference can also cause the key fob not to receive or transmit the signal. This could occur if the key fob is located near a radio transmitter (cell phones and radar detectors) or another source of electromagnetic radiation. The key fob may not work due to a bad connection to the buttons, water damage or damage to the internal chips.

If the key fob has stopped working one day out of the blue, or after trying every option at home to resolve it e.g. replacing batteries, reprogramming or using the spare key fob, you might have a defective receiver module on your 500. The receiver module is located under the dash and receives the radio frequency signals from the key fob. Then, it converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy way to reset all of the onboard systems in your 500 device, including the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electricity and restart the car's computer system, which can help get your key fob working again. If the problem persists you should consult an expert technician. They will be able diagnose the root of any problems.