How to Repair Car Keys

Car keys may appear tiny and insignificant, key repair shops near Me however they are crucial to the operation of your vehicle. Replacing a traditional or a transponder one can cost up to $200.

There are solutions to fix your car keys yourself at less than the cost. This article will address the most frequently encountered car keys problems and the DIY solutions to fix them.

Dead Key Fob Battery

The remote key fobs for keys that come with cars make it simpler than ever to open the trunk, doors, and tailgate. The battery in this device is susceptible to dying. Fortunately, there are a few tricks that can be used to fix this issue in an emergency.

First, make sure that the repair car key remote is in ignition mode. If it is, then the battery of the key fob may simply be low instead of dead. To test this, press the fob's button against the ignition button on the vehicle. If it does not work, the battery is probably fine and only has to be replaced.

To replace the fob's battery, first pry open the case with the help of a screwdriver or watch-type device. Do not apply too much force, as this may cause the fob key repair's casing to split. If the fob doesn't seem to be coming open with ease, try placing your pry tool in several places around the outside of the case.

Once the fob is opened then remove the mechanical key and open the electronic part of the car. Install the new battery and then snap back the shell. If the key fob isn't working after this, there could be a bigger issue with your car's remote start system that requires a professional diagnosis. A reputable mechanic will in a position to assist you if this is the situation. If you require assistance with your vehicle and you need help, you can call roadside assistance.

Broken Key Ring

There are a few steps you can do when your key fob does not work because the ring is broken. First, you must check to see if your broken piece is still inside the ignition. If it is, you should remove it without damaging the door lock or ignition lock. If you have trouble removing it, call a locksmith for help. They have the right tools to safely remove a damaged key from the ignition.

A damaged car key could also be caused by corrosion of the plastic frame or circuit board. You can clean the circuit board by using a cotton swab soaked in ruby alcohol. This will remove the corrosion and stop damage to the contact pads.

If your key isn't starting because the ring is broken, you may be able fix it with a strong wire or nail to plug the hole. Superglue can be used to fix the broken key ring. After cleaning the ring with a wet cloth, apply a small amount superglue to the ends of the wire or nail. Then, press the pieces together and allow them to dry before using your car. These DIY solutions might seem appealing, but they're only a temporary solution. For long-term repairs, you'll want to work with a professional locksmith. They have the expertise and tools to fix the broken key quickly and effectively. They can even replace the battery in your key fob and modify it if necessary.

Broken Key Blade

Some key blades may break due to wear and tear. If this occurs, you must buy a new blade. The issue isn't as serious as you might think at first. The most significant issue is that the blade broke off from the case.

One solution is spraying the key hole with lubricant. Then, you can use pliers, pins, or tweezers to grab the damaged key and pull it out. You may also make use of a magnet if the key is magnetic. Be cautious not to use a magnetic tool on an ignition key since it could cause the tumbler of the lock to break.

If you're not able to get the broken piece of key, call an expert locksmith immediately. They're equipped with special tools that can safely remove keys without causing damage.

Super glue can be used to fix an open lock that has snapped. Apply a small amount of glue to the edges and press them together. Make sure the glue has dried before inserting the key into the lock. This method isn't very reliable, and you might have to repeat it a few times before it works. Plus the super glue may not be strong enough to keep the key in place. This is more of a temporary measure than a permanent solution.

Broken Plastic Loop

If the loop of plastic on your key fob fails it can cause the key to become useless. It's a fairly easy fix. To replace it alternative, you can opt for wire that is thick or a finishing nail. Drill two holes into the broken plastic loop at each end of the wire or nail. Cut the wire or nail to a key width, then put a drop of superglue in each hole. Press the wire or nail into the holes to close them, and then let it dry.

Another option is to get an alternative shell from a locksmith who sells them. They can transfer the programmable section of your key into the new shell, and then cut an entirely new blade at a fraction of the cost.

It's not the most ideal solution, but it will bring you back on the road if your key split in half. It can be difficult to fix the key blade if it is in the ignition. You could try using a hair clip, a needle or an extractor tool to remove the damaged piece of the ignition, but this can be risky if not cautious. Contact a locksmith who has special tools to safely remove damaged keys from ignitions. You can also request a new key made with appropriate cuts for the ignition of your vehicle.

Broken Master Key

You'll need to try to retrieve the key before it is completely destroyed. You can use the tweezers, lubricants and needle nose pliers for grabbing the fragment of a broken key.

To begin, spray the interior of your lock with a lubricant like graphite powder or WD-40. You could also try the hacksaw blade method which involves carefully sliding the blade down along the edge of the broken key, and connecting to a few of the 'teeth'. If you are able to do this, you should be able take the broken key from the lock.

Another tool that is useful is a spiral key extractor, that is available in a wide range of hardware stores. This has a thin flexible bar with spiral threads, which can be put into the keyway, and then bent to reach into the broken part of the mobile key fob repair. Once it has hooked onto the serrations, you can turn it in a circular motion and press it against the broken part of the key to pull it out.

Before contacting a locksmith try to get rid of the broken master key before calling a locksmith. If you can't get the piece out, you need to call the big guns to get a locksmith to make you a brand new key and reprogram it using your car's transponder.