Reasons Your Fiat 500 Key Fob Won't Work

A key fob from fiat ducato replacement key (oy2b33di2G89d2d53r6Oyika.kr) 500 is a convenient way to open the doors and begin the car. However, there are a variety of reasons why the key fob might stop working. This includes a dead coin-battery water damage, problems with the receiver modules, and interference.

This listing is for an NEW replacement fiat key replacement Flip Key Remote that looks like the Ilco brand. It must be professionally programmed (click here to search for local automotive locksmiths). Includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the main reason for your 500 key fob not functioning. Modern key fobs operate with a restricted operating range, and must be within only a few feet from the car to operate. If you're not close to your vehicle and you press the key fob button, the car won't be able to respond, and will display an "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery of your coin cell (Part number CR2032) by a new one from a reputable manufacturer such as Panasonic, Duracell, or Energizer. They are typically available in your local hardware store, or online.

After you've replaced the coin cell battery, you can test it by standing in front of your Fiat 500 and pressing the buttons. The parking lights should light up and the key fob should operate the lock and unlock switches.

If the fob's remote doesn't work after replacing the battery, it could have water damage that prevents it from connecting to the receiver module in your vehicle. Water damage can occur through a variety of methods, including the simple splash or submerging your key fob in saltwater at the beach. If you suspect your fob was exposed to water, try placing it in a dry rice bag to pull the moisture out. If this doesn't work your fob is likely to need to be reprogrammed by an experienced locksmith or dealer.

Water Damage

While the fob has some rubber seals that keep water out of the chip's electronic circuit and out of the ocean or washing it in a machine can cause water damage. Saltwater is especially dangerous to the fob's circuit board that can cause it to short out and eventually end up dying. If you get the fob wet, it's not a good idea, but if you drop it in an empty cup of water, or forget to remove it from your pants pocket before running the washing machine Don't give up hope.

First remove the battery from the fob. Clean the electronic chip with isopropyl alcohol or a similar product and dry it thoroughly before replacing the battery. Next try the fob and see if it works. If the key does not work, it might need to be changed. This is usually done by a dealer or professional auto locksmith.

If the key you have is older and is not programmed for your car, you will need to replace it completely. A professional locksmith in the automotive industry can complete this simple process. The locksmith will have to cut the key to match the ignition on your vehicle. They'll also need to reprogram the fob for your car's system. This is a simple and cost-effective process that is usually completed in the same day.

Receiver Module Issues

One of the main reasons your 500 key fob won't be working is because it's out of range. The remote has a range of 30 feet. So should you be too far from your car it will not respond to your commands. You can easily solve this problem by moving the remote closer to your vehicle until it responds.

If your fob doesn't work after you replace the coin battery, also called a "button", "watch" or "button" or "button", it could be a problem with the internal circuit board. In the majority of cases, reprogramming your fob will solve the problem. The instructions are available for most vehicles on YouTube or in the owner's guide.

It's possible that you need to replace the metal clips that hold the battery of your coin in place. If they loose tension it could hinder the coin battery from being properly seated and can cause your remote to malfunction.

In rare cases the fob might be out of connection with your vehicle as a result of hardware or software problems. This could cause a significant issue, but you are able to often fix this by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In certain instances it may be necessary to reinstall the software on your body control module, as well.

Interference

Interference can also cause the key fob to not receive or transmit a signal. This may happen if the keyfob is in close proximity to a radio transmitter like a cellphone or radar detector. The key fob could not function due to a poor connection with the buttons, water damage or damage to the internal chips.

If the key fob has been unable to function for a while in the middle of the night or after trying everything you can do at home to solve it e.g. You may have a faulty 500 receiver module in the event that you've tried replacing the battery, reprogramming, and using a spare key fob. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

Fortunately, there's an easy method of resetting all of the on-board systems in your 500 device, including the key fob. Disconnect the 12 volt battery for approximately 15 minutes by removing the negative cable first then the positive cable. Then reconnect the battery. This will get rid of any remaining electricity and then restart the car's computers, which could allow you to get your key fob working again. If the issue persists, you should consult an expert technician. They will be able to determine the exact cause of problems.