Window Handle Repair

Window handles may be slack or even broken, allowing the window open to burglars. It's generally not a problem to repair.

Remove the plastic caps at the top and bottom of the handle. This is an easy task that should only take about five minutes with a screwdriver.

Loose Screws

Over time sash windows handle handles can become loose due wear and tear or excessive use. If you feel that it is unstable or uPVC casement windows difficult to open it could be because the screws are loose. This is a simple fix that can be completed with a screwdriver in minutes.

Remove any plastic caps that are covering the screws on the sides and top of the handle. They can be removed using the fingernail or a screwdriver that has a flat head. Once the caps are removed, start with the top screw and tighten it slowly until it is secure. Don't over tighten the screw because it could damage the head. Then, tighten the bottom screw in the same manner. Once both screws are tightened, the handle should be sturdier and open with less difficulty.

If your window handle feels extremely loose or the lock paddle isn't able to be inserted, then it's likely time to replace it with an entirely new crank mechanism. Mail order can be purchased from a wide range of hardware repair experts. It's cheaper than replacing the entire handle. You can also tighten the crank by opening the window and adjusting the crank arm until it aligns with the notch on the guide track. After firmly pushing in the handle, take off any trim mounting screws and lift the casement away from the window jamb. (Photo 1) You will require new trim screws if they are bent or rusted. Compare the new one with the previous one to ensure they match and then install it as illustrated in Photo 5.

Filling screw holes that are not completely filled with wood prior to tightening them is required. Filler should be slightly larger than the screwhole so that it does not pierce the surrounding wood when it's turned in the position.

Broken Spindle

The spindle of your window handle could become worn after a period of time. This can cause the handle to malfunction or stop opening properly. Fortunately, replacing the spindle is a simple and easy fix that can be accomplished by anyone with a few basic tools. It is also crucial to check the alignment of the handle to make sure that it is securely held in place.

It's also a good idea to use a silicone-based lubricant for the spindle and handle following cleaning. This will help it to move more smoothly, eliminating any dirt or other debris that might be obstructing its purpose.

Another common issue with uPVC casement windows is when the locking mechanism fails. This happens when the spindle isn't driven across the wedge block properly by the handle. This can be a real issue as it can stop the window from opening or closing and requiring you to replace either the lock or handle.

This is why it is essential to determine the length of the spindle prior upvc casement windows to buying the replacement. This will help you find a replacement that fits perfectly and also provides a reliable replacement for the handle you have previously purchased. The measurements are typically on the bottom of the handles however if you are unable to locate them, you can contact us to identify the model by calling us.

You can also purchase a complete replacement set of handles that have spindles in order to save time and money. They are usually less expensive and can be put in less time than replacing just the handle.

It's time to contact a professional If your uPVC tilt-and-turn window is still closed even after you've tried all these solutions. A skilled uPVC expert will examine the handle for any issues and give you estimates for repair.

Our selection of replacement uPVC handles includes espag handles, inline, key locking, cranked, and cockspur designs. We stock a large selection of both uPVC and aluminium handle models in a variety of finishes. We can even purchase specific styles for you if we don't have them on hand.

Broken Handle

A damaged handle can cause the uPVC handle to not open at any time. It is usually because the handle is cracked internally, and it is unable to make an attachment to the spindle, and therefore unable to operate the window. This is a common problem with uPVC handles, and is fixable easily by taking the handle off and replacing it with a new one.

This can be done by yourself at home using a screwdriver. To remove the handle you will need a screwdriver lift the plastic cap. The screws on the top and bottom should be visible on the handle base. Using the screwdriver, tighten the top screw until it is secured. Do not tighten too much as this may damage the handle and the frame of the glass.

After ensuring that the handle is securely attached to its base, then replace the second screw, which again should be tightened until solid. Replace the caps made of plastic on both screws, and your aluminium handle will now function as it should.

A damaged gear in the cranking mechanism could also cause the uPVC handle to not open. The handle can turn but not open the window, which could cause many frustrations and can be dangerous for your safety. In this case you must replace the operator mechanism.

This is a simple process and should not take less than a couple of minutes to complete. Bridgewater Glass is happy to help if you are uncomfortable or would like to employ professionals. We have a great deal of experience with uPVC handle repair and replacement and can ensure that your windows are working and safe. Contact us today to discuss our services and learn more about how we can help you.

Broken Base

A window handle can be loose as time passes. Sometimes, it causes the window to tilt or slide open when opened. If this is the case it's usually because one of the screws is not tightening the mechanism to the frame. It's simple to fix it. Just loosen the screw with a hand screwdriver, and then tighten. Close the window, and then move the handle into position.

Sometimes, the handle may completely be separated from the base. This can happen with tilt-and-turn as well as traditional handles. This is very rare and usually only happens in areas with high traffic. This is a simple fix that can be achieved by replacing the old one.

Another common problem is the handle teeth stripping. This usually occurs in the case of older windows with an oversized crank handle. The teeth, which are typically constructed of cast iron, may be ruined through excessive use or age. This is a simple fix and can be fixed with a small vise grip or a pair pliers.

If your handle breaks away from the base, you'll have to take it off to replace it. It can be a bit challenging for an amateur DIYer to complete but it's doable.

First, remove the screw that attaches the crank operator to the window frame. Open the window so that the guide bushing on the crank arm is aligned with a notch on track. Then, using a pair of pliers, push out the window and slide the guide bushing off the crank arm.

After you have removed the old handle take a look at the studs on the crank to determine if the teeth are worn. Then, examine the handle for signs that it's worn. Family Handyman advises that if the splines have worn, you should replace the window crank handle.

To attach the new window crank handle, attach the trim cover to the frame and then reattach any rusted screws. Make sure that the holes for mounting screws are aligned with the holes for mounting on the new handle and then attach the base plate with the remaining screws. Don't over tighten the screw, as this could cause the swivel's swivel shaft to break off the track, and also the nylon roller.