Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are easy to maintain, durable and long-lasting. As opposed to aluminium and timber they do not rust or rot.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will help avoid unnecessary repair costs as well as increase energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause significant damage to your home, and could even be fatal. It is essential to take the time to make sure that you're doing all you can to keep your windows in good condition.

Single-pane windows are fairly simple to replace and will usually fit into the frames that were previously in use very easily. If you have double-paned windows that are joined by internal beading, it will be difficult to remove and replace the old panes. In this instance, window Repair it is necessary to purchase plastic spacers to aid in fitting the new pane into the window frame.

Wearing eye protection and heavy gloves is essential when you are planning to remove the glass by yourself. It is also recommended to lay down a drop cloth before you begin working on the window repair panes, so that any shards of glass fall onto the fabric and not onto the floor which could cause them to be trampled under.

It's a great idea seal the gap after the glass is removed. This will stop drafts and water from getting into your property until a professional is able to repair the window. This will also act as a barrier, preventing any intruders from gaining entry to your home. If the gap is particularly large, you may be interested in a security door that has an integrated window as it offers the best of both worlds.

2. Sagging

uPVC windows and doors are a cost-effective energy efficient, durable and long-lasting alternative to timber windows made of sash. However, over time, they are susceptible to a range of problems including sagging. A window that isn't properly aligned can cause problems with light, draughts and even security. It is crucial to act immediately if you discover that your uPVC windows are sagging.

Repositioning the hinges can aid in fixing a window which is sagging. To do this, you'll have to open the window to get to the frame. With a screwdriver, you can take off the hinges on the top and bottom and adjust them by turning them clockwise or counter-clockwise. Close your window to test the fit after you have relocated your hinges. If you're satisfied with the fit, you can tighten the screws to ensure they remain in place.

If you are unable to move the hinges, you might have to replace the seal. Seals made of rubber can dry out and lose their elasticity over time, causing them to loose their elasticity. It is essential to replace your seal as quickly as you can to keep your uPVC window watertight and draughtproof.

UPVC handles can also become loose. Often it is due to screws that have come loose over time. However, it can also happen because the handle mechanism has been worn out. Luckily, it's not difficult to repair the handle of a window that is loose yourself. First, you'll need to close your window and do an initial test to ensure that it fits. The joint at the corners of the sash must align with the joint on the casing. If it isn't, you can use the screwdriver to loosen the handle. Then, you can turn the mechanism into position.

3. Water Leaks

If you're waking up to wet floors and damp walls each time it rains it's crucial to take action. Windows that leak water do not only lead to the degrading of the structure of your home but also hinder your efforts to regulate the temperature within your home. Most often, uPVC window leaks are caused by a damaged or missing sealant.

This is a simple fix that can be done by anyone who is a DIYer with the skills. Depending on the severity of the problem the caulking that was used up might need to be removed before a new layer of caulk can be applied. It is crucial to keep in mind that when it is about uPVC window repairs, do not be tempted to apply too much caulk' as this will only make the area more difficult to clean and decrease the efficiency of your energy usage.

It is essential to ensure that the drainage holes are clear of debris and that the sill pan has been angled correctly so that it drains away from the window. In more extreme cases, you may need to replace the window.

Mold spots and rotten sills are other signs of water leakage. This fungus thrives in conditions of dampness and can spread quickly throughout the home.

It is also important to note that if the leakage originates from the glass of your double glazed windows, it's more likely to be an issue with the glass seal, rather than the frame or sagging. A uPVC specialist can easily solve this problem by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your upvc window repair windows are brittle to open, or slack and blow open with ease It could be the hinges that are at fault. These are easily repaired by any skilled DIYer and are usually completed in just a few minutes.

Like any mechanical component hinges are prone to wear out over time. The process of replacing a hinge on a window is essentially a simple process but it can be easier when you have a person to help hold the frame in place.

Check that the uPVC hinges open and close in the right direction. This can be done by checking for the arrows on each hinge, this indicates which way the window should be opened.

The problem can be caused either by opening the window improperly or a faulty installation at the factory. It is usually possible to fix the issue by sending us a photo through our website and we will be more than happy to give you advice.

Regularly lubricating the hinges is also necessary. This can be done by applying a light engineering oil on the hinges. We recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It also helps prevent corrosion and reduce the possibility of sticking. Ideally, you should do this once a year. WD40 and other solvent-based oils are not recommended because they will damage parts of your uPVC window.

5. Draughts

Draughts in windows made of upvc can be caused by a variety of various factors. The hinges may also become misaligned due to wear, which can cause a gap between the frame and sash. They can be fixed by giving them a good clean, but when they're beyond repair, it could be necessary to have them re-aligned or replaced. The interlock, which is on the hinge side of the window, may be misaligned. Again, it may be feasible to give them a thorough clean, however in some instances it could be necessary to have these replaced.

These seals can wear down or be damaged over time, allowing air to escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of Upvc with low-emissivity glasses. This will help control indoor temperatures, and reduce the possibility of draughts.

One of the most effective ways to cut down on the draughts in your home is to use a draught excluder. These are usually fabric tubes filled with some sort of filler and can be placed on top of your windowsill. They will help stop cold air from entering and keep your home warm and cosy!

The windows made of upvc can continue to provide excellent insulation and security in your home with a little regular maintenance and repairs. However, it is important to recognize that all windows have a life span and eventually, they will reach an point at which it is more efficient to replace them than repair them. If you encounter any issues with your Upvc window you should consult an expert as soon as possible.