Replacing uPVC Window Handles

It is simple to swap the handles on windows made of upvc. The important thing is to ensure that the new handle is a good fit for the spindle that was cut out of the window mechanism.

If the steps listed below are followed the cockspur handle will fit in most windows. The height of the step of the handle is crucial.

What to look for

As time passes, uPVC handles on many windows in the UK begin to show signs wear and tear. If this happens, the window handle could become shaky or difficult to operate, making it essential to replace it. This is a simple task that can be completed by anyone who is familiar with basic hand tools.

The first step is to ensure that the handle is securely fixed to the frame of the window and in the open position. The next step is to locate the fixing screws or pins that hold the handle in the position it is in. These are typically located on the inside of the handle and are removed with a screwdriver, or pliers.

Once the handle has become loose, gently pull it away from its hinges. Then, you'll have to locate a new handle that is the same dimensions and style. This can be done online or at the local DIY store and should take five minutes using a screwdriver.

When replacing the handle of a uPVC handle, it is important to think about the step height. This is the distance from the bottom of the handle to the point at which it is placed on the frame of the window. This is a standard measurement and you should confirm the height of the step prior to ordering an replacement handle.

There are a variety of sizes based on the kind of handle. Inline handles for upvc windows (source web page) generally feature lug centers of 31mm, and there are also cockspur handle types that have 43mm centres. Tilt-and-turn handles are commonly found on uPVC windows. They have a special design which allows the window be tilted for ventilation, and then turned to fully open the window.

The most frequent uPVC handle cracks are internal, rather than a breakage from the base. This can make it difficult to open. It is crucial to ensure that any replacement handle is fitted with the same spindle that was used in your original one.

Remove the old Handle

Incorrectly installed or damaged window handles could cause double glazed window handle-glazed windows to close or open in a way that isn't correct and may cause them to become stuck. There are a variety of reasons for this including general wear and tear or the corrosion of the metal handle. In these cases, it is important to locate replacement upvc window handles as soon as you can to avoid further damage and loss of functionality.

One of the first things to do when replacing window handles made of upvc is to remove the old handle from the window. To do this, start by taking off the screw that is encased when the handle is in a closed position. This should reveal another screw, and once it is removed, you can begin to remove the handle itself. It is a good idea to employ an electric screwdriver to accomplish this, as it makes the task easier and quicker.

It is also worth noting that the handles' screws could be hidden behind caps made of plastic, so it is recommended to use a Stanley knife to the screw caps and then take them off. After removing the old handle, you'll be required to inspect the square cutout on the base to make sure that the new handle for the window sash lock door handles is compatible. It is essential to measure the spindle length on the handle that was used and then compare it with the dimensions of the window mechanism spindle cutout.

There are three kinds of upvc handles: Espag handles with a central screw that can be turned right or left and Cranked handles that have two screws, and Spade handles which have arms that are flat and can be used on either side of the window made of upvc. It is easy to replace the handle when you have found one that is suitable. Just put it in place and ensure that the spindle is inserted correctly into the euro lock handles mechanism. After you have done this you can tighten the handle onto the window frame. The replacement upvc handle will now be secured.

Take a look at the Spindle

If you're replacing a upvc window handle that has fallen off, it's due to the spindle that holds it in place has become loose or damaged. In some cases this can be fixed by using pins or screws to secure it. In other situations, it will need to be replaced entirely. There are a variety of upvc handles. They include espagnolette handles that are inline or cockspur handles. They also have tilt and turn handles. Each type of handle is mounted and replaced in a different fashion.

It is crucial to measure the current handle before purchasing the replacement. This will ensure that the new handle is the right size and fits into the window. All handles are measured according to industry standards, so it is easy to find the correct size.

To determine the size of your handle, first remove it from the window by turning it to an open position. You should be able see the dimensions of the screw or pin that secures the handle. Use a ruler or tape measure to determine the length the spindle is. Once you have the length of your spindle, it is possible to purchase a replacement of exactly the same size.

The step height of a upvc window handle is another factor to consider when purchasing an alternative. The step height is measured from the base to the point where the handle is positioned on the frame. This usually is about 21mm or 9mm for aluminium and uPVC. To ensure that the new handle will fit the gap, drop something into the space to check how far it goes before meeting an obstruction.

Cockspur handles usually have different backset heights, based on the type of window they're installed in. Inline espag handle heights are 43mm from centre to center (two fixing points). Cockspur handles, however they have different backsets depending on the style of the window they're in. This is because they feature a spur that extends from the handle and is secured over the cockspur wedge striker plate.

Install the New Handle

After you have chosen the new handle, make sure it is aligned with the screw holes on the door. Secure it using the screws supplied. If you're also replacing the latch lever the lever can be mounted similarly to the main door handle. After that, attach the door trim again to hide the screws for mounting.

Tips: To remove the metal head from a wooden wedge, place the handle on the floor so that its wide end is on the floor. Then, you can use to tap the thin end. Be careful not damage the handle or spindle.