Replacement UPVC Door Handles

If you're replacing your handles or adding a little more security, you can choose the perfect handle for your door. These upvc handle are easy to install and have the minimum 92mm central distance for multipoint locks.

The backplate fixing center and the keyhole/lever dimensions are the most important measurements. Check these carefully against your current measurements prior to ordering.

Lever/Pad

Lever pad handles consist of a lever on one side and a handle that is shaped like a paddle on the other. They are intended for use with key wind locks. However, they can be fitted to multipoint split spindle door locks.

Our range of old upvc door handles handles lever pads are available in a variety of finishes and these will be listed in the drop-down list after you have selected the correct handle for your door. Not all styles of handles are available in every finish and you should always check the sizes and technical drawings for the specific product you're looking for to ensure that you get the correct size and fit.

When selecting new upvc lever pad door handles it is important to ensure that they match the PZ (distance between the handle spindle and the centre of the hole for the cylinder) of your existing multipoint locks, since they have to be in line for the doors to remain locked, whether from the inside or the outside. Our handles are designed to fit most standard cylinders, but it is always worth double-checking before ordering.

If you wish to upgrade to dual spindle levers you will need to remove the existing handles and take apart the lock case. This will require an additional split cylinder inline. These can be bought separately and we have the complete technical diagram to look at in the images for each product.

Once you have removed the screws holding the door handle you have, it is recommended to loosen them and examine the mechanism to see the condition it is in. If the screws aren't tight enough, you may need to loosen them further. Then, you can remove the spindle from the door handle and replace it with a new upvc handle. It is important to ensure that the handle is in the proper position before fixing it. You can do this by placing your finger between the frame and the handle to ensure that it's level.

Lever/Lever

Lever door handles are an a multi-point lock using a Euro cylinder. They can be found on most replacement double glazing handles doors made of upvc, aluminum doors, and some wooden doors. They feature a lever on the inside and an outside paddle and are generally available in two different types. Sprung - These include a spring cassette within the backplate that helps bring the handle lever into the horizontal position. Non-sprung - these do not have a spring mechanism and must be manually pulled to bring the handle lever back to its horizontal position.

To fix the door handle lever that is sliding you'll need to locate the detent access pin or hole. It's usually small, protruding ring, or rectangle, found on the handle base plate. Once located you can loosen the set screw using the help of a screwdriver, and then take it off to allow the lever, allowing it to return to the horizontal position.

When the handle is in a horizontal position you can put the screws back in place and tighten them so that the handle stays secured to the base plate. You should also consider applying an adhesive that locks the screw threads to improve the grip and prevent them from loosening over time.

Lever door handles that droop could be the result of various causes. The most frequent reason is that the fixings have been too tightened and are putting strain on the bearings that are and causing it to pull against the door face. It could also be because the levers are not being operated at a straight angle and this is causing the latch mechanism preventing it from fully springing back into service.

Another common reason is that the lever that is sprung is not operating correctly and this is typically due to the spring not being in the correct position within the backplate. The most effective way to determine this is to operate the handle and see whether it changes to its horizontal position.

It is crucial to repair any loose door handles as soon as you can. This could cause excessive wear on the screws, and the handle might be able to fall off the base plate. You should also tighten any loose screws on a regular basis to stop them from becoming looser.

Lever/Snib

These upvc door handles are also known as 'Snib' handles and have a snib lever on the top of the lever that can be pressed down to lock your door if you don't use a fake lock. They are usually fitted with a Fullex 68PZ (that's 68mm between the spindle's centre and the lever or the lock centre) door lock. We also stock a range of door handles 68PZ from manufacturers like Ferco and Fab & Fix.

Change your door handle is a cost-effective method to upgrade your home, whether you're replacing your handles or installing new ones on doors you've built in your house. There are many styles of upvc door handle available with traditional levers on backplate, curved or straight short latch and knob handles that resemble dummy knobs for multi point locks which are perfect for French doors.

Lever on backplate handles are typically rectangular in shape, however there are also oval or circular-shaped models that are referred to as rose door handles. These kinds of door handles have the knob or lever on a backplate, which sits behind the lever or knob and is sometimes referred to as a rosette, although certain back plates can be detached to be concealed for fixing.

These handles are available in a variety of finishes including chrome and coloured finishes to be matched to your door and hardware, such as knobs bolts and hinges. Some handles are equipped with a grub screw to attach the lever or knob firmly to the spindle. Other handles are supplied with bathroom spindles that can be used to operate bathroom locks and incorporate a thumbturn turn and release mechanism, which is ideal for use on bathroom doors.

Mortise

The tubular latch is the most likely to be the culprit in the event that your door handle is stuck open. There are a few things that can cause this, the most common being a simple lack of lubrication on the latch plate. It is possible to fix this problem by opening the door and spraying lubricant on the handle and lock. It could also be that the latch is loose from the backplate. This could be more complicated and would require a professional to fix it.

A multipoint handle is the best solution for a stuck door handle. These handles mount through the faceplate of the door and are operated with the thumb turn knob or key that triggers a cam that locks the deadbolt. The handles are available in a variety of sizes to fit various kinds of uPVC door and in various attractive finishes that complement the hardware that is currently in use. The handles are available via the internet or at an authorized locksmith in your area. They are easy to install and come with clear directions.

To select a replacement upvc window handles handle set, you will be required to determine the PZ dimension of your cylinder. This is the distance from the edge of the inner frame of the door to the central point of the handle hole in millimetres. You will also need to determine if the door is hook locks or a mortise-style lock. The easiest way to find the correct handle after you have the measurements is to use the filter for brands on the website. This will narrow down the options and you can then choose the appropriate size from the list.

A typical handle set includes the handle unit with a pair of various length screws drilling guides, as well as installation instructions. Smarter versions, such as the Igloohome Smart Mortise 2+ include a mortice lock with a keypad. These are more complicated devices that are suited to professionals or highly skilled DIYers. Certain handle sets come with many accessories, such as weather strips, which can be used to improve the appearance of the door.