How to Replace a kia keys replacement Sportage Replacement Key

For a number of Kia models keys, there is the keyless entry system that is built into the key. This key usually resembles an electronic remote and is able to be replaced by a new one purchased from a Kia dealer or a locksmith.

Key fobs can stop working due to various reasons, such as an empty coin battery, worn buttons, water damage, signal interference and a malfunctioning receiver module. Here are some tips on how to get your Kia Sportage replacement key to function again.

How do you replace a remote key or smartkey

The battery inside your Kia's smart key will eventually need be replaced, regardless of whether it is a remote key as well as a push-to start key or a regular key that doesn't have a transponder. This is especially relevant if your vehicle displays a message telling you that the remote or smart keys have low battery power.

Luckily, it's quite simple to do. To replace the battery of the key fob, remove the mechanical key from the slit in the back of the key fob. Next, lift the cover. Inside the key fob there will be an incredibly small screw that holds the battery in its place. By using a small screwdriver loosen the screw and pull out the battery that was in place. Then, insert the new and close the slit inside the key fob.

Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock in the same way, you're set! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you have to do some errands in Brandon.

Note: Some keys may require to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or locksmith has access to. Other keys (non transponder keys made of metal) don't require programming. If you want to change the programming of your key, you'll have to note the key code number on the tag for the key code.

How do I replace a battery

If the Kia key fob is unable to respond to pressing the lock/unlock button, it is most likely that the battery is low. A battery that is not functioning properly could cause other issues, such as the check engine light flashing on or a delay in cranking the engine. Fortunately, replacing the battery on the key fob is a simple DIY project that requires only a few basic tools.

Before you begin be sure that your vehicle is off and all doors are closed. Find the small metal or a plastic piece near the bottom of the key fob. Jiggle it until the metal key is released. Then, you can insert the key in the door handle of the driver to open your car.

To replace the battery inside the key fob, remove the rear cover. Use a plastic pry tool to open the latch that holds the black negative cable. Remove the old battery, and then orient the replacement battery to ensure that its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or bending the contacts made of metal.

After installing the new battery, turn the key fob on and off in the ignition until the door locks up. You can then test the Kia's key fob again to make sure it's functioning properly.

How can you replace the smart key

Depending on the model of the Kia Sportage, you may have a standard key fob or a smart key. The smart key features an embedded mechanical key blade while the standard key fob does not. Both key fobs are equipped with an internal battery that will eventually need to be changed. It's an easy task that only takes about two minutes.

Before you get started it is important to ensure that you are on a flat surface with adequate lighting and that your Kia is turned off. Also, keep in mind that there are small parts inside the fob that could be removed if not vigilant.

The release button for the small size is located on the lower backside. This will either be a circular silver button or a rectangular slot. Once you press this the mechanical key blade will appear and you will be able to open the key fob.

After the key fob has been open, remove the battery that was in it. The new battery should be a CR-2032 and can be bought online or from your local auto parts store. After installation you should be able to lock or unlock your car using your key fob - even if your engine isn't running!

How do you replace a broken mechanical key

The Kia keyfob is a great convenience which allows us to lock or unlock our car by simply pressing the button. Like any other device, the Kia key fob can have issues at times. There are steps that can be taken to troubleshoot these issues and ensure that our key fobs are in good working condition for the long run.

A dead or low-quality battery is among the most frequent problems. This can cause the fob to cease working or work intermittently. If this is the problem then replace the battery with an entirely new battery.

If this does not resolve the issue, you can use the flathead screwdriver that is standard to wedge the fob's plastic casing open. Be careful not to harm any internal components or scratch the plastic. When the battery is open, carefully take off the battery you have been using and replace it with a brand new one.

Close and open the door using the mechanical key. (Every kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to confirm it's functioning properly. If the fob still isn't working, call a dealer or locksmith to help solve the problem. To avoid a lockout in the future make sure you get an emergency key that can be able to work with all door and trunk cylinders.