Repairs to uPVC Windows

uPVC windows are an excellent choice for modern homes. They are long-lasting, durable and easy to maintain. Unlike timber and aluminium, they do not rust or rot.

It is important to clean and oil UPVC doors and windows regularly. This will prevent unnecessary repair costs as well as increase energy efficiency.

1. Broken Glass

The broken glass in your windows can cause serious damage to your home and even be fatal. It is important to ensure that your windows are in good condition.

Single-pane windows are relatively simple to replace and typically fit into frames of the past easily. However, if windows with double panes are secured by internal beading, it'll be more difficult to take out the existing panes and install new ones. In this case you'll need to source some plastic spacers to help the new pane to fit correctly into the frame of the window.

Wearing eye protection and heavy gloves is essential for anyone who plans to remove the glass yourself. It is also recommended to lay down a drop cloth before you begin working on the window panes so that any shards fall on the fabric and not onto the floor and could be trampled.

Once the glass has been removed, it's a good idea to seal the gap with packaging tape or duct tape to block water and drafts from entering the property until a professional comes out and fix the window. This will also act as a barrier, deterring any intruders from gaining entry to your home. If the distance between the door and the window is substantial, you may prefer an alarm system that includes a window. This will provide the best of both.

2. Sagging

uPVC windows and doors are a cost-effective, durable and energy-efficient alternative to timber sash windows. However, over time they can suffer from a variety of problems including sliding. A sagging window in uPVC can cause issues with light, draughts and even security. If you notice that your uPVC window is beginning to shrink, it's important to act quickly to stop the issue from getting worse.

To fix a window that is sagging you can try to reposition the hinges. First, you'll need to open the windows to access the frame. Then, remove both the hinges at the top and bottom using a screwdriver, and then adjust them clockwise or counter-clockwise. Once you've repositioned the hinges, close the window and test it for fitting. If you're satisfied with the fit, you can tighten the screws until they stay in place.

If you are unable to move the hinges, you could have to replace the seal. As time passes, rubber seals lose their elasticity and become dry, which causes them to loosen. It is crucial to replace your seal as quickly as you can in order to ensure that your uPVC window watertight and draughtproof.

upvc repair handles can also loosen up. The majority of the time, this is caused by screws that have become loose over time. However, it can be due to the fact that the handle mechanism has been worn out. It's fairly simple to repair a loose uPVC handle. The first step is to close your window and do an experiment to ensure that it fits. The joint at the corners of the sash should be aligned with the joint on the casing. If it doesn't, you can make use of a screwdriver to loosen the handle and turn the mechanism back into its original position.

3. Water Leaks

It is essential to take action if you wake up every morning to find a smoky wall and wet floors. Water leaks through windows can cause structural damage to your home and impact your ability to regulate the temperature of your home. The most common cause for leaks in uPVC windows is that the sealant surrounding the frame is damaged or missing.

This is a fairly simple fix that can be done by any competent DIYer. Depending on the severity of the issue the caulking used previously may require removal before a new layer of caulk can be put on. It is important to keep in mind that when it is about uPVC window repairs, you should not be tempted to apply too much caulk in order to make the area more difficult to clean and reduce the efficiency of your energy.

Verify that the drainage holes do not have debris inside them and that the sill pan is properly angled to allow the water to drain from the window. In more serious situations, you may have to replace the window.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives in humid conditions and can propagate quickly throughout the house.

It is also important to note that if the leak originates from the glass of your double glazed windows, it is more likely to be a problem with the glass seal rather than the frame or sagging. This can be easily repaired by a uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or are loose and blow open with ease It could be hinges that are at the fault. These are easily repaired by any skilled DIYer and can be completed in just a few minutes.

Like any mechanical part hinges will be damaged over time. It is very easy to change a window hinge, but it's easier if someone helps you to hold the frame.

Make sure that the uPVC hinges open and close in the proper direction. Look for the arrows that are on each hinge to determine the direction in which the window should be opened.

The issue can be caused by opening the window improperly or by a poor Upvc window repairs installation in the factory. Sending us photos via our website is often enough to resolve the problem. We are more than happy to give assistance.

It is also crucial to lubricate the hinges on a regular basis. This can be done by applying a light engineering oil on the hinges. We recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can make the window easier to open and close. It also decreases the possibility of a window sticking and prevent corrosion. This must be done at a minimum every year. WD40 and other solvent-based lubricants are not recommended as they can damage your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different causes. The hinges can also become unbalanced due to wear, which can cause an opening between the frame and sash. These can be easily fixed by giving them a good cleaning, but in the event that they are beyond repair it may be necessary to have them aligned or replaced. The second is the interlock, which is located on the hinge of the window and UPVC Window Repairs can be misaligned. Again, it may be possible to give them a good clean, but in some cases it might be necessary to get them replaced.

These seals are susceptible to wear and tear or get damaged over time, allowing air escape. Replacing these with high-quality weatherstripping can help keep draughts at bay. Replace the windows made of upvc with low-emissivity lenses. This will help to regulate indoor temperatures, and reduce the risk of draughts.

The final method to cut down on drafts effectively is to use a draught-excluder. These are usually fabric tubes filled with a filler which can be hung over your window sill. These will keep your home warm by blocking cold air.

With a little regular maintenance and repair your windows made of upvc will continue to provide excellent security and insulation for your home. However, it is important to realize that all windows have a lifespan and eventually, they will reach an point at which it is more efficient to replace them than fix them. So, if you are experiencing issues with your Upvc windows, it is always recommended to seek assistance from a professional immediately.